Easy and excellent application. No bubbles immediately. It combines perfectly with the spigen armor 605CS25800 case with great results! Nice texture and does not affect fingerprint.

Rugs, it doesn't stick to the edges at all and the little hairs they give you to lay it down gather it up and crinkle it just when you think you've succeeded. It's better to take the film out of each envelope and stick it with uhu stick.

Jelly is terrible..you pay 10 euros for 2 pieces.....they're not even worth 1. I applied it as shown in the company's videos and from the first day it didn't adhere well. The next day, the corners where the screen curves came off....it's not worth it, get something else.....

The problem is that it is difficult to adjust on the curved screen. If you apply more pressure, it takes a long time to bring it to the right place. I followed the instructions, but in many points on the curved screen, it didn't stick at all. As a protection, it is fine and does not affect the screen and touch. For extra protection, only a glass.

Very easy application. There is a good guide with videos. No comparison to anything else I had tried so far. The print works perfectly and the bubbles disappeared the next day!!

It has good application on the screen although the issue with the hole in the camera and the position it should be placed confuses the situation a bit! The positive thing is that compared to more expensive protectors, the fingerprint function works satisfactorily!

After dozens of screen protectors that I tried, only this one works quickly and reliably. The fingerprint also does not come off on the curved surface of the screen and in the corners.

Applied according to the instructions! The next day, every remaining bubble had disappeared! After two months, it easily caught air and dust on the side, and I had to replace it! It requires a lot of attention because it easily comes off!

4 stars for the difficulty in installation. It requires great attention during application and VERY careful movements. However, if it is applied correctly, I consider it to be top-notch in its category with great durability. Much superior in quality compared to the corresponding model for the S9 that I had, which after a while did not allow the finger to slide as easily and was more "rough" in its construction. Of course, compared to the classic "glass" it lacks the smoothness in your hand since it is not as smooth, but this is something that happens with all membrane-type protections. However, I believe that it blends better with the phone compared to a glass, covering the entire screen, giving you the impression of a body. The fingerprint recognition is also a plus, without any difficulty or delay.

Quite a hassle to install.
Impossible to get rid of the air bubbles.
Rejected.

Update: Most of the air bubbles disappeared. Changing my rating from 2 to 4.

It was very easy to install and without having done too many.
The liquid helps a lot in easy placement.
In terms of touch, I think it is very good and in my opinion, after using 2 tempered glasses, it is much better.
It has been installed on a Samsung S10 and is fully compatible, of course, with the Spigen case.
The only downside is that on a black screen and under specific angles, the membrane creates something like water, which fortunately is not visible when the phone is in use or simply cannot be distinguished

Good for plastic protection film, but that's about it. It applies easily and perfectly, it just needs a little patience for a few minutes to dry. If applied correctly, it does not peel off.
When the screen is off, at certain angles it is visible that something is on the screen, the film has some very light "wrinkles", hardly visible but existent.
It is very durable. Indeed, it is difficult to scratch, as it has a sticky, rubbery texture. And here is its big problem, the feel. It doesn't resemble glass at all and the finger doesn't easily glide over it. Overall, it's not bad, but I will try something else next time.

I have installed dozens of front panels, this one was difficult to install, it didn't fit well, it centered the camera hole incorrectly and had excess material elsewhere, and vice versa. And with both pieces, it didn't do the job and they fell off. Such a waste of my money

I had bought the SAMSUNG screen protector and it came off after 2 weeks, plus it left the front camera area completely exposed, on the top right. I applied this specific one and within 3 minutes it was perfectly installed on my GALAXY S10. The fingerprint works perfectly, the screen is not affected at all, and everything functions flawlessly.
Update 20/6 The only downside is that it leaves a "film" visible on the screen, mainly noticeable in bright sunlight and with sunglasses. That's it. Fingerprint, screen, etc., everything works perfectly just like the first day of installation.