Skroutz.mt

Siemens Iq300 Ventilation Mechanism 70cm Inox
Vent Hoods

Siemens Iq300 Ventilation Mechanism 70cm Inox Code: LB75565

Key features:

  • 2 Metal filters (washable)
  • Motor: 200 W
  • Noise Level: 44 dB
  • Maximum suction power: 590 m³/h

The Maan company's vent hood with an extraction power of 590 m³/h, which can adequately cover areas up to 14m².

See full description

  • Item

    Absorption Mechanism

    "They are built-in hoods that are installed in cabinets and only the bottom surface of the hood is visible, additionally they do not have sliding filters."

  • Noise Level

    Shows how much noise the extractor makes when it is in operation.

    2. The fewer the db, the quieter it is. An extractor with 58db or less is considered quite quiet.

  • Energy class

    The energy class categorizes devices into groups according to the current they consume, ranging from the lowest D to the highest A+++.

    2. The higher the energy class, the lower the electricity consumption.

    3. For example, for a 12 sq.m. kitchen with an extractor fan that has an absorption power of about 340m³/h and frequent weekly use, the difference in annual cost from D to A is about €6, and from A to A+++ the difference is almost negligible.

  • Extraction Power (Max)

    Displays the maximum absorption capacity. To calculate the required absorbency, knowledge of the dimensions of the kitchen space is necessary.


    For example, for a 7 sqm kitchen, the required absorption power is approximately 200m³/h, for 12 sqm it is approximately 340m³/h, and for 15 sqm it is 420m³/h and above.

  • Filter Type

    Charcoal (optional)

    Carbon filters are used when range hoods operate without a duct connection and the air is recirculated into the room.


    They are not washable and it is recommended to replace them every 4 months.


    Their use reduces the efficiency of the range hood by about 30%.

    Metal

    They are used in most extractors. Metallic filters are easy to remove and clean, either in the dishwasher or by hand. They do not require frequent replacement.
  • See all
This product is temporarily unavailable at Skroutz Last updated: 6 days ago
Product report

Description

Description

Dimensions

  • Length: 53 cm
  • Depth: 35 cm
  • Height: 25.5 cm


Specifications

  • Type: Built-in
  • Width: 53 cm
  • Dimensions (HxWxD): 25.5 x 53 x 35 cm
  • Maximum Suction Power: 590 m³/h
  • Operating Levels: 4
  • Energy Consumption: C
  • Motors: 2
  • Color: Gray-Metallic
  • Annual Energy Consumption: 78.1 kWh
  • Grease Retention Efficiency: C
  • Filter Type: Metal filters
  • Noise Level: 56 dB
  • Filter Replacement Capability: Metal & Activated Carbon
  • Weight: 8 kg
  • Supplier Warranty: 2 years
  • Light Intensity: 438 lux (2 x 2.15W)
  • Color Temperature: 3500 K
  • Control with sliding buttons
  • Connection cable with plug 1.3 m

Manufacturer

Manufacturer Details

Warnings & Safety Information
See full description

Specifications

Specifications

Product Number
LB75565

Product Details

Type
Absorption Mechanism

Type

Absorption Mechanism
"They are built-in hoods that are installed in cabinets and only the bottom surface of the hood is visible, additionally they do not have sliding filters."
Retro
No
Grease Filter Material
Charcoal (optional), Metal

Grease Filter Material

Charcoal (optional)

Carbon filters are used when range hoods operate without a duct connection and the air is recirculated into the room.


They are not washable and it is recommended to replace them every 4 months.


Their use reduces the efficiency of the range hood by about 30%.

Metal

They are used in most extractors. Metallic filters are easy to remove and clean, either in the dishwasher or by hand. They do not require frequent replacement.
Extraction Mode
Extraction or Recirculation

Extraction Mode

Concerns the way in which the extractor absorbs air.

Extraction or Recirculation

The extractor fan has both functions. The air that the extractor fan draws can either be extracted through a pipe or recycled back into the fan. For air extraction function, a pipe is needed to remove the air outside the kitchen.
Dual Motor
No
Type of Control
Switches
Timer Function
No
Filter Cleaning Indicator
No
Washable Filter
-
Colour
Inox

Technical Features

Extraction Power (Max)
379 m³/h

Extraction Power (Max)

Displays the maximum absorption capacity. To calculate the required absorbency, knowledge of the dimensions of the kitchen space is necessary.


For example, for a 7 sqm kitchen, the required absorption power is approximately 200m³/h, for 12 sqm it is approximately 340m³/h, and for 15 sqm it is 420m³/h and above.
Extraction Power (Boost)
638 m³/h

Extraction Power (Boost)

The boost power enhances absorption even more for a short period of time. After a while, it returns to maximum absorption.


The function is ideal for odors during frying and grilling.

Dimensions

Width
70 cm
Length
35 cm

Energy Label

Energy Class
C

Energy Class

The energy class categorizes devices into groups according to the current they consume, ranging from the lowest D to the highest A+++.

2. The higher the energy class, the lower the electricity consumption.

3. For example, for a 12 sq.m. kitchen with an extractor fan that has an absorption power of about 340m³/h and frequent weekly use, the difference in annual cost from D to A is about €6, and from A to A+++ the difference is almost negligible.
Average Energy Consumption per Year
81 kWh/y
Extraction Flow Efficiency
D

Extraction Flow Efficiency

Expresses how effective the extractor is in absorbing odors. 2. The performance scale starts at G for less efficient extractors and goes up to A for more efficient ones. 3. Typically, a rating of D and above is a good performance for effectively absorbing odors from cooking.
Lighting Efficiency
A

Lighting Efficiency

Expresses the intensity of the hood's lighting. The scale starts from G for the lowest performance where the lighting is quite soft, up to A for the highest performance where the lighting is more intense. It is usually recommended to have a lighting performance index of C or higher to facilitate cooking with more intense lighting.
Fat Retention Efficiency
B

Fat Retention Efficiency

Shows how effectively the filters of the extractor work in retaining fat. 


The scale starts from G for the lowest performance, up to A for the highest performance. 


A performance rating of C and above is considered satisfactory for fat retention during cooking.
Noise Level
56 dB

Noise Level

Shows how much noise the extractor makes when it is in operation.

2. The fewer the db, the quieter it is. An extractor with 58db or less is considered quite quiet.

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

See all specifications

Reviews (2)

Reviews

5.0
2
5.0
Review this product
  1. 2
  2. 4 stars
    0
  3. 3 stars
    0
  4. 2 stars
    0
  5. 1 star
    0
Review this product

Reviews by our members

  • andriop
    5
    11 out of 11 members found this review helpful
    andriop

    I have had it for 3 months. It replaced a noisy 70cm Teka extractor hood with a 12-year-old motor (Siemens has 2 motors), which was struggling to suck even on the 3rd setting. Be aware, it is larger compared to other 70cm extractor hoods (3cm longer and 7cm wider than the one I had) and I had to cut a lot of wood to make it fit. For maximum performance and low noise, the company recommends direct extraction through a 150mm round duct and prohibits the use of a transition from round to rectangular duct. Although I used the reducer provided in the packaging (from round 150mm to 125mm) and then to a rectangular duct so that it doesn't show above the cabinets (something that increases noise and reduces suction according to the manufacturer), I have to say the following in summary:
    a) it is really low noise,
    b) it pulls satisfactorily from the 2nd setting (it has a total of 4 settings),
    c) it has very strong lighting, and
    d) it is relatively expensive but, in my opinion, worth its money.

    Translated from Greek ·
    • Performance
    • Relatively quiet
    • Construction quality
    • Value for money
    • Is its lighting satisfactory?
    Did you find this review helpful?
  • 5
    5 out of 5 members found this review helpful
    kallia1121

    It is powerful, "pulls" very well. It doesn't make noise, except at the highest setting.

    Translated from Greek ·
    • Performance
    • Relatively quiet
    • Construction quality
    • Value for money
    Did you find this review helpful?
  • andriop
    5
    andriop

    I have had it for 3 months. It replaced a noisy 70cm Teka extractor hood with a 12-year-old motor (Siemens has 2 motors), which was struggling to suck even on the 3rd setting. Be aware, it is larger compared to other 70cm extractor hoods (3cm longer and 7cm wider than the one I had) and I had to cut a lot of wood to make it fit. For maximum performance and low noise, the company recommends direct extraction through a 150mm round duct and prohibits the use of a transition from round to rectangular duct. Although I used the reducer provided in the packaging (from round 150mm to 125mm) and then to a rectangular duct so that it doesn't show above the cabinets (something that increases noise and reduces suction according to the manufacturer), I have to say the following in summary:
    a) it is really low noise,
    b) it pulls satisfactorily from the 2nd setting (it has a total of 4 settings),
    c) it has very strong lighting, and
    d) it is relatively expensive but, in my opinion, worth its money.

    Translated from Greek ·
    11
  • 5
    kallia1121

    It is powerful, "pulls" very well. It doesn't make noise, except at the highest setting.

    Translated from Greek ·
    5
  • See all

Description & Specifications

Dimensions

  • Length: 53 cm
  • Depth: 35 cm
  • Height: 25.5 cm


Specifications

  • Type: Built-in
  • Width: 53 cm
  • Dimensions (HxWxD): 25.5 x 53 x 35 cm
  • Maximum Suction Power: 590 m³/h
  • Operating Levels: 4
  • Energy Consumption: C
  • Motors: 2
  • Color: Gray-Metallic
  • Annual Energy Consumption: 78.1 kWh
  • Grease Retention Efficiency: C
  • Filter Type: Metal filters
  • Noise Level: 56 dB
  • Filter Replacement Capability: Metal & Activated Carbon
  • Weight: 8 kg
  • Supplier Warranty: 2 years
  • Light Intensity: 438 lux (2 x 2.15W)
  • Color Temperature: 3500 K
  • Control with sliding buttons
  • Connection cable with plug 1.3 m

Manufacturer

Manufacturer Details

Warnings & Safety Information
Product Number
LB75565

Product Details

Type
Absorption Mechanism

Type

Absorption Mechanism
"They are built-in hoods that are installed in cabinets and only the bottom surface of the hood is visible, additionally they do not have sliding filters."
Retro
No
Grease Filter Material
Charcoal (optional), Metal

Grease Filter Material

Charcoal (optional)

Carbon filters are used when range hoods operate without a duct connection and the air is recirculated into the room.


They are not washable and it is recommended to replace them every 4 months.


Their use reduces the efficiency of the range hood by about 30%.

Metal

They are used in most extractors. Metallic filters are easy to remove and clean, either in the dishwasher or by hand. They do not require frequent replacement.
Extraction Mode
Extraction or Recirculation

Extraction Mode

Concerns the way in which the extractor absorbs air.

Extraction or Recirculation

The extractor fan has both functions. The air that the extractor fan draws can either be extracted through a pipe or recycled back into the fan. For air extraction function, a pipe is needed to remove the air outside the kitchen.
Dual Motor
No
Type of Control
Switches
Timer Function
No
Filter Cleaning Indicator
No
Washable Filter
-
Colour
Inox

Technical Features

Extraction Power (Max)
379 m³/h

Extraction Power (Max)

Displays the maximum absorption capacity. To calculate the required absorbency, knowledge of the dimensions of the kitchen space is necessary.


For example, for a 7 sqm kitchen, the required absorption power is approximately 200m³/h, for 12 sqm it is approximately 340m³/h, and for 15 sqm it is 420m³/h and above.
Extraction Power (Boost)
638 m³/h

Extraction Power (Boost)

The boost power enhances absorption even more for a short period of time. After a while, it returns to maximum absorption.


The function is ideal for odors during frying and grilling.

Dimensions

Width
70 cm
Length
35 cm

Energy Label

Energy Class
C

Energy Class

The energy class categorizes devices into groups according to the current they consume, ranging from the lowest D to the highest A+++.

2. The higher the energy class, the lower the electricity consumption.

3. For example, for a 12 sq.m. kitchen with an extractor fan that has an absorption power of about 340m³/h and frequent weekly use, the difference in annual cost from D to A is about €6, and from A to A+++ the difference is almost negligible.
Average Energy Consumption per Year
81 kWh/y
Extraction Flow Efficiency
D

Extraction Flow Efficiency

Expresses how effective the extractor is in absorbing odors. 2. The performance scale starts at G for less efficient extractors and goes up to A for more efficient ones. 3. Typically, a rating of D and above is a good performance for effectively absorbing odors from cooking.
Lighting Efficiency
A

Lighting Efficiency

Expresses the intensity of the hood's lighting. The scale starts from G for the lowest performance where the lighting is quite soft, up to A for the highest performance where the lighting is more intense. It is usually recommended to have a lighting performance index of C or higher to facilitate cooking with more intense lighting.
Fat Retention Efficiency
B

Fat Retention Efficiency

Shows how effectively the filters of the extractor work in retaining fat. 


The scale starts from G for the lowest performance, up to A for the highest performance. 


A performance rating of C and above is considered satisfactory for fat retention during cooking.
Noise Level
56 dB

Noise Level

Shows how much noise the extractor makes when it is in operation.

2. The fewer the db, the quieter it is. An extractor with 58db or less is considered quite quiet.

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

Reviews (2)

5.0
2
5.0
Review this product
  1. 2
  2. 4 stars
    0
  3. 3 stars
    0
  4. 2 stars
    0
  5. 1 star
    0
Review this product

Reviews by our members

  • andriop
    5
    11 out of 11 members found this review helpful
    andriop

    I have had it for 3 months. It replaced a noisy 70cm Teka extractor hood with a 12-year-old motor (Siemens has 2 motors), which was struggling to suck even on the 3rd setting. Be aware, it is larger compared to other 70cm extractor hoods (3cm longer and 7cm wider than the one I had) and I had to cut a lot of wood to make it fit. For maximum performance and low noise, the company recommends direct extraction through a 150mm round duct and prohibits the use of a transition from round to rectangular duct. Although I used the reducer provided in the packaging (from round 150mm to 125mm) and then to a rectangular duct so that it doesn't show above the cabinets (something that increases noise and reduces suction according to the manufacturer), I have to say the following in summary:
    a) it is really low noise,
    b) it pulls satisfactorily from the 2nd setting (it has a total of 4 settings),
    c) it has very strong lighting, and
    d) it is relatively expensive but, in my opinion, worth its money.

    Translated from Greek ·
    • Performance
    • Relatively quiet
    • Construction quality
    • Value for money
    • Is its lighting satisfactory?
    Did you find this review helpful?
  • 5
    5 out of 5 members found this review helpful
    kallia1121

    It is powerful, "pulls" very well. It doesn't make noise, except at the highest setting.

    Translated from Greek ·
    • Performance
    • Relatively quiet
    • Construction quality
    • Value for money
    Did you find this review helpful?
  • andriop
    5
    andriop

    I have had it for 3 months. It replaced a noisy 70cm Teka extractor hood with a 12-year-old motor (Siemens has 2 motors), which was struggling to suck even on the 3rd setting. Be aware, it is larger compared to other 70cm extractor hoods (3cm longer and 7cm wider than the one I had) and I had to cut a lot of wood to make it fit. For maximum performance and low noise, the company recommends direct extraction through a 150mm round duct and prohibits the use of a transition from round to rectangular duct. Although I used the reducer provided in the packaging (from round 150mm to 125mm) and then to a rectangular duct so that it doesn't show above the cabinets (something that increases noise and reduces suction according to the manufacturer), I have to say the following in summary:
    a) it is really low noise,
    b) it pulls satisfactorily from the 2nd setting (it has a total of 4 settings),
    c) it has very strong lighting, and
    d) it is relatively expensive but, in my opinion, worth its money.

    Translated from Greek ·
    11
  • 5
    kallia1121

    It is powerful, "pulls" very well. It doesn't make noise, except at the highest setting.

    Translated from Greek ·
    5
  • See all