Review for the 20lt model:
I placed it in a basement/warehouse of 115+ sq.m. and within 2 days it reduced the humidity from 65-70% to the limit of 55% with a steady consumption of ~3.5kWh/day (it is connected to a smart Tapo socket). Only in the first 24 hours it struggled a bit and consumed 5-6kWh. It seems to draw a steady power of 240-250w whether the UV is activated or not. The wifi consumes less than 5w, however, if someone doesn't use it properly, they should turn it off using the relevant button as over time they will save something. Measured with at least 5 hygrometers from different manufacturers placed in various locations, which have variances of up to 5% between them, but the reduction in humidity is noticeable overall, as observed in all the hygrometers.
When it reaches its limit, it stops and if I understand correctly, it starts again only when the humidity increases by about 3-4%. However, there have been times when I set it at 55%, it reduced the humidity to 53% and continued to work normally (i.e. at 250w).
In theory, the humidity can go even lower, but I haven't tested it yet. With the limit set at 55% and the current humidity, my tank fills up about 2 times per day, so I will install a drain pipe to send it directly to a drain (note that it doesn't have a motor for water outlet, so the last part must be drained based on the slope of the pipe only). The package also includes a drain pipe of about half a meter (I don't remember the exact diameter, I think it is mentioned in the manual and it is around 14mm or something like that). The tank also has the disadvantage that its lid doesn't close tightly and it leaks from everywhere, so during emptying, the water cannot come out from a specific point. Practically, water runs from the upper edge from all sides and you need to be careful not to make a mess when emptying it.
It is definitely not silent. There is a constant humming throughout the space and when it starts or generally increases its speed, for a few minutes it sounds like the characteristic sound of old refrigerator motors. Also, sometimes it rattles loudly. It doesn't bother me in the basement, but I would never leave it in the living room or bedroom, especially during quiet hours. It makes much more noise than a typical air conditioner or air purifier, etc.
On the plus side, the pre-installed plastic feet can be replaced with wheels (included in the package). The connection and use with wifi are simple, but the Ewpe application is simply unacceptable (possibly the worst of the dozens of similar ones I have tried over time). Most of the time, it returns a timeout error the first time until it manages to connect to the device, it cannot connect to Alexa (the last step always fails even when the relevant skill is enabled), it doesn't send notifications when the tank is full, etc.
Overall, it seems to do the job and is worth its money, however, it can be improved.
ps: I see in the reviews photos with the back of the device almost stuck to the wall. I hope that is not its permanent position because the dehumidifier draws air from the back and the manual recommends a distance of at least 35-40cm both from the back and from its left side, which is the air outlet.
UPDATE after 3 months of use: It does what it's supposed to do. Likewise, it makes noise. I am still trying to understand the difference in settings between High and Low fan, as they practically make almost the same noise and burn almost the same wattage (maybe High burns about 10% more, at most). Generally, I always have it on High and running for 12-18 hours a day, burning over 100-110 kWh per month. I haven't experienced any disconnections from the wifi, although the Ewpe app always times out after 30" before it manages to connect on the second attempt.
But what I really haven't understood is how it starts and stops on its own:
- If you set it, for example, to a humidity level of 55% and it has stopped earlier on its own, then usually it will only start again when the sensor reaches 60%.
- With the same humidity setting, it usually stops when it reaches around 51-52% and often not even then. Because I have been using it exclusively with the internal tank, at some point it would fill up, and the device would stop working for hours (before reaching 51-52%), and once I emptied the tank, the device would start again on its own. So far so good. The problem was that it would do this even when it measured the humidity at 53-54%, which is below the 55% that I have set. It shouldn't start in that case.
- Lately, I have connected it to a drain. Although its setting is still at 55%, it practically never stops working. It reduces the humidity to 47-50% according to 4-5 hygrometers scattered in the room, but the dehumidifier itself never shows below 52% and obviously, for some inexplicable reason, it doesn't stop. When I tried to increase the setting to 60%, the humidity in the basement exceeded 65% before the device started, so I didn't try it again.
Since the Ewpe app doesn't seem to have a schedule or timer on (only timer off), I had to set a program through Alexa so that it flashes for a few hours a day either automatically or with voice commands. Luckily, at some point, the relevant Ewpe skill of Alexa was activated without me having to do anything (previously it would fail at authentication). So far, I have only done it based on time, but I will try to do the same based on humidity percentages, which Alexa seems to read. So I will be able to turn it on automatically if it reaches, for example, 58% and also turn it off if it drops to 53%. We'll see.
Review για το μοντέλο 20lt:
Τον έβαλα σε υπόγειο/αποθήκη 115+ τ.μ. και μέσα σε 2 μέρες έριξε την υγρασία από 65-70% στο όριο του 55% με σταθερή κατανάλωση ~3.5kWh/μέρα (είναι πάνω σε smart πρίζα Tapo). Μόνο το πρώτο 24ωρο ζορίστηκε λίγο και έκαψε 5-6kWh. Φαίνεται να τραβάει σταθερή ισχύ 240-250w είτε με το UV ενεργοποιημένο είτε χωρίς. Το wifi τραβάει λιγότερα από 5w, ωστόσο αν κάποιος δεν το χρησιμοποιεί καλά θα είναι να το σβήνει από το σχετικό κουμπί αφού σε βάθος χρόνου όλο και κάτι θα γλυτώσει. Μετρημένο με τουλάχιστον 5 υγρόμετρα διαφορετικών κατασκευαστών τοποθετημένων σε διάφορα σημεία, που ναι μεν έχουν αποκλίσεις έως 5% μεταξύ τους αλλά η ελάττωση της υγρασίας είναι συνολικά αισθητή που παρατηρήθηκε σε όλα τα υγρόμετρα.
Όταν πιάσει το όριό του, τότε σταματάει και αν έχω καταλάβει καλά ξεκινάει πάλι μόνο όταν αυτό ανέβει ένα 3-4%. Έχει τύχει όμως να το βάλω στο 55%, να κατεβάσει την υγρασία στο 53% και να συνεχίσει να δουλεύει κανονικά (δηλ. στα 250w).
Θεωρητικά η υγρασία μπορεί να κατέβει και λιγότερο, αλλά δεν το έχω δοκιμάσει ακόμα. Με το όριο στο 55% και την υγρασία που έχω αυτή την περίοδο το δοχείο μου γεμίζει περίπου 2 φορές/24ωρο οπότε θα τοποθετηθεί αλφαδοσωλήνας για να στέλνει απευθείας σε αποχέτευση (προσοχή ότι δεν έχει μοτέρ για την έξοδο του νερού, οπότε το τελευταίο αναγκαστικά πρέπει να διοχετεύεται βάσει της κλίσης του σωλήνα και μόνο). Στη συσκευασία περιλαμβάνεται αλφαδοσωλήνας μισού περίπου μέτρου (δεν θυμάμαι ακριβώς τη διατομή, νομίζω την αναφέρει το manual και είναι κάπου 14mm ή κάτι τέτοιο). Το δοχείο επίσης έχει το μειονέκτημα ότι το καπάκι του δεν κλείνει στεγανά αλλά μπάζει από παντού, οπότε κατά το άδειασμα αποκλείεται να βγαίνει το νερό μόνο από συγκεκριμένο σημείο. Πρακτικά τρέχει νερό από το πάνω χείλος από όλες τις μεριές και χρειάζεται προσοχή για να μην λερώσουμε όταν αδειάζουμε.
Σε καμία περίπτωση δεν είναι αθόρυβος. Υπάρχει διαρκές βουητό σε όλο το χώρο ενώ όταν ξεκινάει ή γενικά ανεβάζει στροφές, για κάποια λεπτά ακούγεται σαν τον χαρακτηριστικό ήχο των παλιών μοτέρ ψυγείου. Επίσης ορισμένες φορές συντονίζει και ακούγεται ένα έντονο τρίξιμο. Στο υπόγειο δεν με ενοχλεί, σε καμία περίπτωση όμως δεν θα το άφηνα σε σαλόνι ή κρεβατοκάμαρα, ειδικά σε ώρες ησυχίας. Κάνει πολύ περισσότερο θόρυβο από τυπικό κλιματιστικό ή καθαριστή αέρα κλπ.
Στα συν ότι τα προεγκατεστημένα πλαστικά ποδαράκια μπορούν να αντικατασταθούν από ροδάκια (περιλαμβάνονται στη συσκευασία). Η σύνδεση και χρήση με wifi είναι μεν απλή, αλλά η εφαρμογή Ewpe είναι επιεικώς απαράδεκτη (πιθανώς η χειρότερη από τις δεκάδες του είδους που έχω δοκιμάσει κατά καιρούς). Τις περισσότερες φορές επιστρέφει timeout την πρώτη φορά μέχρι να καταφέρει να συνδεθεί με το μηχάνημα, δεν μπορεί να συνδεθεί με Alexa (αποτυγχάνει πάντα το τελευταίο βήμα ακόμα κι όταν είναι ενεργοποιημένο το σχετικό skill), δεν στέλνει notification όταν γεμίσει ο κάδος κλπ.
Γενικά φαίνεται να κάνει δουλειά και αξίζει τα λεφτά του, ωστόσο επιδέχεται βελτιώσεων.
ps: βλέπω στα reviews φωτογραφίες με την πλάτη της συσκευής σχεδόν κολλημένη σε τοίχο. Ελπίζω ότι δεν είναι η μόνιμη θέση της, γιατί ο αφυγραντήρας απορροφά τον αέρα από την πίσω μεριά και το manual συνιστά απόσταση τουλάχιστον 35-40εκ τόσο από την πλάτη, όσο και από την αριστερή του μεριά που είναι η έξοδος του αέρα.
UPDATE μετά από 3 μήνες χρήσης: Ό,τι κάνει δουλειά, κάνει. Ομοίως ότι κάνει φασαρία. Ακόμα προσπαθώ να καταλάβω ποια είναι διαφορά στη ρύθμιση μεταξύ High και Low fan, αφού πρακτικά κάνουν περίπου τον ίδιο θόρυβο και καίνε σχεδόν τα ίδια Watt (ίσως το High να καίει ένα 10% παραπάνω, το πολύ). Γενικά το έχω μόνιμα σε High και με λειτουργία 12-18 ωρών τη μέρα, καίει πάνω από 100-110kWh/μήνα. Αποσυνδέσεις από το wifi δεν έχω δει, αν και η εφαρμογή Ewpe ΠΑΝΤΑ κάνει ένα timeout μετά από 30" πριν καταφέρει να συνδεθεί με τη δεύτερη προσπάθεια.
Αυτό όμως που πραγματικά δεν έχω καταλάβει είναι με ποια λογική ξεκινάει και σταματάει από μόνο του:
- Αν του βάλεις πχ. ρύθμιση για υγρασία 55% και έχει σταματήσει νωρίτερα από μόνο του, τότε συνήθως θα ξαναπάρει μπροστά μόνο όταν ο αισθητήρας φτάσει στο 60%.
- Με ίδια ρύθμιση υγρασίας, συνήθως σταματάει όταν φτάσει γύρω στο 51-52% και συχνά ούτε καν τότε. Επειδή τόσο καιρό το λειτουργούσα αποκλειστικά με την εσωτερική δεξαμενή, κάποια στιγμή αυτή γέμιζε, η συσκευή σταματούσε να δουλεύει για ώρες (πριν φτάσει στο 51-52%), αναγκαστικά η υγρασία ανέβαινε και προφανώς μόλις άδειαζα το δοχείο η συσκευή άρχιζε πάλι από μόνη της. Μέχρι εδώ καλά. Το πρόβλημα ήταν πως αυτό το έκανε ακόμα κι όταν μετρούσε την υγρασία στο 53-54%, δηλαδή κάτω από το 55% που τον έχω ρυθμίσει. Κανονικά δεν θα έπρεπε να ξεκινάει.
- Τελευταία τον έχω συνδέσει με αλφαδολάστιχο και αποχέτευση. Παρ' ότι η ρύθμισή του εξακολουθεί να είναι στο 55%, πρακτικά δεν σταματάει να δουλεύει σχεδόν ποτέ. Ρίχνει την υγρασία στο 47-50% σύμφωνα με 4-5 υγρασιόμετρα διασκορπισμένα στο χώρο, αλλά ο ίδιος ο αφυγραντήρας δεν δείχνει ποτέ κάτω από 52% και προφανώς για κάποιο ανεξήγητο λόγο δεν σταματάει. Όταν δοκίμασα να ανεβάσω λίγο τη ρύθμιση στο 60%, η υγρασία στο υπόγειο ξεπέρασε το 65% μέχρι να πάρει μπροστά η συσκευή οπότε δεν το ξαναδοκίμασα.
Επειδή το Ewpe app δεν φαίνεται να έχει schedule ή timer on (παρά μόνο timer off), αναγκάστηκα να του βάλω πρόγραμμα μέσω Alexa ώστε να αναβοσβήνει για κάποιες ώρες τη μέρα είτε αυτόματα είτε με φωνητικές εντολές. Ευτυχώς κάπου στο ενδιάμεσο ενεργοποιήθηκε το σχετικό Ewpe skill της Alexa χωρίς να χρειαστεί να κάνω κάτι (παλιότερα έσκαγε στο authentication). Μέχρι τώρα το έκανα μόνο βάσει ώρας, αλλά θα δοκιμάσω να κάνω το ίδιο και μέσω ποσοστών υγρασίας, που φαίνεται να τα διαβάζει η Alexa. Οπότε θα μπορώ να το ανάβω αυτόματα αν φτάσει πχ 58% και ομοίως να το σβήνω αν πέσει στο 53%. Θα δείξει.