Skroutz.mt

Powermat Cutting Machine IGBT CUT-50 PM-PP-50L Plasma Cutting Inverter 50A
Welding Machines

Powermat Cutting Machine IGBT CUT-50 PM-PP-50L Plasma Cutting Inverter 50A

IGBT Cutting Machine

See full description

  • Welding Current

    50

    Suitable for use on thin sheets and DIY constructions.

  • Duty Cycle

    The Duty Cycle is the portion of a ten-minute period that a welding machine can operate continuously at maximum Amperes before it needs to stop and cool down.

    2.

    For example, a welding machine with a maximum Amperage of 200 A and a Duty Cycle of 30% can operate continuously at 200 A for 3 minutes before it needs to stop.

  • Power Supply Voltage

    230

    It is the supply voltage that the machine requires from the electrical grid.

  • Power

    6.5

    Affects the power consumption of the machine and determines if it can be supported by the electrical network you are using.
  • See all
The product is not available for shipping to the selected country.
Review the product
Product report

Description

Description

Allows the cutting of electrically conductive materials, such as non-alloyed, alloy, precious steel, aluminum, copper, nickel, or cast iron. It features IGBT technology, which provides the highest efficiency. The cutting current is very stable. Allows cutting with current up to 50A, at a 60% duty cycle, which enables cutting materials up to 12 mm.

The cutting machine activates the arc in HF mode (high-frequency ignition) - defines the non-contact start of an electric arc using high frequency, which creates a clean starting point. The advantage of using compressed air is the ability to cut at high speeds while maintaining a high cutting surface. The ability to cut without burning thin materials and a small cutting gap are additional advantages of the device.

Cooled by a high-speed fan, while the thermal switch disconnects the device in case of exceeding the allowable duty cycle for a given welding current, preventing it from overheating.

Features

  • IGBT Technology
  • No-load voltage: 230V
  • Power consumption: up to 6.5kVA
  • Ignition type: HF (non-contact)
  • Cutting depth: 15mm
  • Quality cutting depth: 10mm
  • Cutting current range: 20 - 50A
  • Operating voltage range: 88-100V
  • Cutting current with 100% duty cycle: 39A
  • Rated duty cycle: 60%
  • Required air pressure: 3.5 - 5 bar
  • Air demand: 120l/min

Package Contents

  • Ground cable 200cm
  • Gas hose 200cm
  • Plasma cutting hand plate 405cm
  • Built-in pressure reducer with pressure gauge

Manufacturer

Manufacturer Details

Warnings & Safety Information
See full description

Specifications

Specifications

Dimensions

Type
Plasma Cutting

Type

Plasma Cutting

It uses compressed air to cut almost any type of metal with speed and precision. At 50A, it can cut metal up to 2.5cm thick. 2. It is mainly used by specialized personnel in workshops (e.g. car repairs).
Welding Current (max)
50 A

Welding Current (max): 50


Suitable for use on thin sheets and DIY constructions.
Operation Cycle (max Ampere)
60 %

Operation Cycle (max Ampere)

The Duty Cycle is the portion of a ten-minute period that a welding machine can operate continuously at maximum Amperes before it needs to stop and cool down.

2.

For example, a welding machine with a maximum Amperage of 200 A and a Duty Cycle of 30% can operate continuously at 200 A for 3 minutes before it needs to stop.
Supply Voltage
230 V

Supply Voltage: 230


It is the supply voltage that the machine requires from the electrical grid.
Power
6.5 kVA

Power: 6.5


Affects the power consumption of the machine and determines if it can be supported by the electrical network you are using.
Weight
9000 gr

Additional Features

Inverter
Yes

Inverter


New technology welding. Very good in terms of performance, durability, and weight, but with a high cost of repair in case of damage. They have automation for better and safer work. If connected to a generator, it is recommended to choose one with 8kVA or more.
IGBT
Yes

IGBT


Allows the conversion of direct current (DC) voltage to alternating current (AC) or the output of direct current at a higher or lower intensity.
VRD
No
with Voltage Stabilizer
No
for Generator with AVR
No

Features

Hot Start
No
Anti Stick
No
Arc Force
No
2T Operation
No
4T Mode
No
Spot Function
No
Pulsed
No

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

See all specifications

Description & Specifications

Allows the cutting of electrically conductive materials, such as non-alloyed, alloy, precious steel, aluminum, copper, nickel, or cast iron. It features IGBT technology, which provides the highest efficiency. The cutting current is very stable. Allows cutting with current up to 50A, at a 60% duty cycle, which enables cutting materials up to 12 mm.

The cutting machine activates the arc in HF mode (high-frequency ignition) - defines the non-contact start of an electric arc using high frequency, which creates a clean starting point. The advantage of using compressed air is the ability to cut at high speeds while maintaining a high cutting surface. The ability to cut without burning thin materials and a small cutting gap are additional advantages of the device.

Cooled by a high-speed fan, while the thermal switch disconnects the device in case of exceeding the allowable duty cycle for a given welding current, preventing it from overheating.

Features

  • IGBT Technology
  • No-load voltage: 230V
  • Power consumption: up to 6.5kVA
  • Ignition type: HF (non-contact)
  • Cutting depth: 15mm
  • Quality cutting depth: 10mm
  • Cutting current range: 20 - 50A
  • Operating voltage range: 88-100V
  • Cutting current with 100% duty cycle: 39A
  • Rated duty cycle: 60%
  • Required air pressure: 3.5 - 5 bar
  • Air demand: 120l/min

Package Contents

  • Ground cable 200cm
  • Gas hose 200cm
  • Plasma cutting hand plate 405cm
  • Built-in pressure reducer with pressure gauge

Manufacturer

Manufacturer Details

Warnings & Safety Information

Dimensions

Type
Plasma Cutting

Type

Plasma Cutting

It uses compressed air to cut almost any type of metal with speed and precision. At 50A, it can cut metal up to 2.5cm thick. 2. It is mainly used by specialized personnel in workshops (e.g. car repairs).
Welding Current (max)
50 A

Welding Current (max): 50


Suitable for use on thin sheets and DIY constructions.
Operation Cycle (max Ampere)
60 %

Operation Cycle (max Ampere)

The Duty Cycle is the portion of a ten-minute period that a welding machine can operate continuously at maximum Amperes before it needs to stop and cool down.

2.

For example, a welding machine with a maximum Amperage of 200 A and a Duty Cycle of 30% can operate continuously at 200 A for 3 minutes before it needs to stop.
Supply Voltage
230 V

Supply Voltage: 230


It is the supply voltage that the machine requires from the electrical grid.
Power
6.5 kVA

Power: 6.5


Affects the power consumption of the machine and determines if it can be supported by the electrical network you are using.
Weight
9000 gr

Additional Features

Inverter
Yes

Inverter


New technology welding. Very good in terms of performance, durability, and weight, but with a high cost of repair in case of damage. They have automation for better and safer work. If connected to a generator, it is recommended to choose one with 8kVA or more.
IGBT
Yes

IGBT


Allows the conversion of direct current (DC) voltage to alternating current (AC) or the output of direct current at a higher or lower intensity.
VRD
No
with Voltage Stabilizer
No
for Generator with AVR
No

Features

Hot Start
No
Anti Stick
No
Arc Force
No
2T Operation
No
4T Mode
No
Spot Function
No
Pulsed
No

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.