Sensors

Adafruit Sensor Accelerometer 163 1pcs

The Adafruit accelerometer measures acceleration along the X, Y and Z axes and provides three analog outputs. The onboard regulator converts an input of up to 5 V to a 3.3 V output. The analog output...

The Adafruit accelerometer measures acceleration along the X, Y and Z axes and provides three analog outputs. The onboard regulator converts an input of up to 5 V to a 3.3 V output. The analog output voltage ranges from 0 V at -3 g to 3.3 V at 3 g, with 0 g indicated at 1.65 V.

The board is fully assembled and tested. It includes an 8-pin header with 0.1"...

See full description See full description
22 41 €
Delivery by Fri, 13 Nov
14,00 €   shipping cost
Sent from Greece
From Top Electronics 4.9 (40)

Learn more about invoicing

Description

Description

The Adafruit accelerometer measures acceleration along the X, Y and Z axes and provides three analog outputs. The onboard regulator converts an input of up to 5 V to a 3.3 V output. The analog output voltage ranges from 0 V at -3 g to 3.3 V at 3 g, with 0 g indicated at 1.65 V.

The board is fully assembled and tested. It includes an 8-pin header with 0.1" spacing for connecting to a breadboard or perfboard, as well as two 2 mm mounting holes. The filtering capacitors for the XYZ axes are 0.1 μF, and the bandwidth is 50 Hz.

  • Type: Accelerometer
  • Measurement axes: X, Y and Z
  • Outputs: 3 analog
  • Measurement range: -3 g to 3 g
  • Input voltage: Up to 5 V
  • Regulator output voltage: 3.3 V
  • Output voltage at 0 g: 1.65 V
  • Filtering capacitors: 0.1 μF
  • Bandwidth: 50 Hz
  • Header: 8-pin with 0.1" spacing
  • Mounting holes: 2 holes, 2 mm in diameter
  • Length: 19 mm
  • Width: 19 mm
  • Height: 3.14 mm
  • Weight: 1.27 g

Manufacturer

See full description

Specifications

Specifications

Type
Accelerometer

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

See all specifications

Description & Specifications

The Adafruit accelerometer measures acceleration along the X, Y and Z axes and provides three analog outputs. The onboard regulator converts an input of up to 5 V to a 3.3 V output. The analog output voltage ranges from 0 V at -3 g to 3.3 V at 3 g, with 0 g indicated at 1.65 V.

The board is fully assembled and tested. It includes an 8-pin header with 0.1" spacing for connecting to a breadboard or perfboard, as well as two 2 mm mounting holes. The filtering capacitors for the XYZ axes are 0.1 μF, and the bandwidth is 50 Hz.

  • Type: Accelerometer
  • Measurement axes: X, Y and Z
  • Outputs: 3 analog
  • Measurement range: -3 g to 3 g
  • Input voltage: Up to 5 V
  • Regulator output voltage: 3.3 V
  • Output voltage at 0 g: 1.65 V
  • Filtering capacitors: 0.1 μF
  • Bandwidth: 50 Hz
  • Header: 8-pin with 0.1" spacing
  • Mounting holes: 2 holes, 2 mm in diameter
  • Length: 19 mm
  • Width: 19 mm
  • Height: 3.14 mm
  • Weight: 1.27 g

Manufacturer

Type
Accelerometer

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

22,41 €
14,00 €   shipping cost