Skroutz.mt

Gardena 11000 Aquasensor Single-phase Pump Waste Water / Sewage 0.6hp 09034-20
Submersible Water Pumps

Gardena 11000 Aquasensor Single-phase Pump Waste Water / Sewage 0.6hp 09034-20

Key features:

  • Maximum pump submersion: 7m
  • Cable length: 10m
  • Power: 450W
  • Output: 11000 lit/h
  • Maximum head height: 7m
  • Maximum pressure: 0.7 bar
See full description

  • Horsepower

    Horsepower indicates the kinetic power of the pump. Higher horsepower means more efficiency in water pumping, affecting the flow (l/h) and the head (m).

  • Voltage

    Single-Phase

    Single-phase power supply refers to the provision of electrical energy from single-phase current (e.g., 230V AC), which is the most common type of supply for residential and small commercial applications. 

  • Power

    It is the energy consumed by the motor to pump water. The greater the power, the more effectively it can lift and move water, especially over long distances or heights.

  • Manometric Height

    7

    The Maximum Head Height refers to the maximum height at which the pump can lift water against resistance (such as pipes or filters). As the head height increases, the pump's flow rate decreases.

    • The maximum head height is considered by manufacturers to be the point where the water will just barely reach.
    • The maximum performance is considered by manufacturers to be the water flow at 0-1 meter head height.
  • See all
The product is not available for shipping to the selected country.
Review the product
Product report

Description

Description

The Gardena 11000 is a powerful and highly efficient clean water drainage pump with an innovative Aquasensor system. Suitable for use in a flooded basement due to rain or for emptying a pool, either in these specific cases or in many other possible scenarios. With this particularly powerful pump, you save energy and it will prove to be an essential addition to your home and garden toolkit.

Extremely efficient thanks to innovative technologies

It has a power of 450 W and pumps up to 11000 liters of clean or slightly dirty water per hour at a pressure of 0.7 bar and a maximum submersion depth of up to 7 m. With a flat suction of just 1 mm, your floor will need a quick wipe for a dry result. This is truly a high-performance and energy-efficient pump

Innovative Aquasensor System

It features modern and innovative characteristics provided by the digital LED Aquasensor. This innovation allows for use in tight spaces, and the pump's activation and deactivation heights can be precisely adjusted with touch control. For example, it can automatically start operating from a water level of just 5 mm - ideal for protecting basements from flooding. The Aquasensor measures the current water level without direct contact and displays the value using a readable LED indicator. 

A useful timer function and an intuitive touch function are also included. The Aquasensor eliminates the risk of dry running, protecting the pump from potential damage. But it is not only the internal functions and self-protective technologies of the GARDENA pump that will impress you.

Powerful, versatile, and efficient

With a maximum depth of 7 m at a pressure of 0.7 bar, the pump is particularly powerful and suitable for various applications. It allows practical flat suction up to 1 mm.

Durable, safe, and completely waterproof

The outer casing is top-notch in terms of durability and design. The stainless steel casing not only looks good but also effectively protects the pump from external damage. The motor shaft has a ceramic coating with triple sealing that includes an oil chamber for even greater durability. Additionally, the drainage pump has an equally useful built-in function for maximum flow rate or dry run shutdown. The user-friendly flow boost switch at the base can push the pump if flat suction is not required to enhance the pump's performance.

Easy GARDENA Hose Connection System

The Drainage Pump 11000 Aquasensor for Clean Water allows the connection of flexible hoses with a diameter of 32 mm (1 ¼ "), 38 mm (1 ½") or 50 mm (2 ") and the connection with a G1 ½ thread for further options.

Specifications

  • Maximum pump submersion: 7m
  • Cable length: 10m
  • Power: 450W
  • Output: 11000 lit/h
  • Maximum head height: 7m
  • Maximum pressure: 0.7 bar
  • Maximum liquid temperature: 35 °C
  • Power cable type: H05 RNF 
  • Electrical protection category: IP X8

Manufacturer

Manufacturer Details

Warnings & Safety Information
See full description

Specifications

Specifications

Dimensions

Type
Waste Water / Sewage

Type

Waste Water / Sewage

Waste water / sewage pumps are used for pumping and transporting waste water, sewage, and other liquids containing solids or particles
Power Source
Electric

Power Source

Electric
The power supply refers to the pump's need for electrical energy from an external power source, such as single-phase or three-phase power.
Voltage
Single-Phase

Voltage

Single-Phase

Single-phase power supply refers to the provision of electrical energy from single-phase current (e.g., 230V AC), which is the most common type of supply for residential and small commercial applications. 
Horsepower
0.6 hp

Horsepower

Horsepower indicates the kinetic power of the pump. Higher horsepower means more efficiency in water pumping, affecting the flow (l/h) and the head (m).
Power
450 W

Power

It is the energy consumed by the motor to pump water. The greater the power, the more effectively it can lift and move water, especially over long distances or heights.
Cable Length
10 m

Features

Electronic Level Sensor
Yes

Electronic Level Sensor

It automatically activates the pump without the classic hanging float switch. It is ideal for narrow spaces and pits, as there is no risk of it getting stuck anywhere and flooding the area.
with Cutter Impeller
No

with Cutter Impeller

Components that chop, "cut" solid materials, such as organic waste or other particles, before they pass into the pump. They are mainly used in sewage or dirty water pumps, preventing clogging or damage to the system.
Float switch
Yes

Float switch

It is a mechanism that automatically controls the operation of the pump. When the water level reaches a predetermined height, the float activates the pump.
Outlet Nozzle
1/2"

Outlet Nozzle

The outlet nozzle refers to the point or the external diameter of the pump from which the pumped water or liquid exits. It is an important feature for determining the connection of the pump with the piping system and affects the flow capacity of the liquid.
Vortex
No

Vortex

The vortex system in submersible water pumps uses vortex technology to create a rotating water current, which helps in the efficient transfer of water, even when it contains particles or solids.

Pumping Specifications

Maximum Head Height
7 m

Maximum Head Height: 7


The Maximum Head Height refers to the maximum height at which the pump can lift water against resistance (such as pipes or filters). As the head height increases, the pump's flow rate decreases.

  • The maximum head height is considered by manufacturers to be the point where the water will just barely reach.
  • The maximum performance is considered by manufacturers to be the water flow at 0-1 meter head height.
Maximum Output
11 m³/h

Maximum Output

The maximum output or flow of a submersible water pump, as defined by the manufacturers, is the maximum amount of water the pump can move under ideal conditions, usually with zero head (i.e., no lift resistance).
Pump Submersion Depth
7 m
Maximum Particle Size
47.8 mm

Maximum Particle Size

Specifies the largest size of solid particles (such as sand, stones, or other impurities) that the device can pump without clogging or being damaged.
Shallow Suction
Yes

Shallow Suction

This function allows the pump to suck water from an extremely low level (up to 1-3 mm), ideal for flooded floors and basements.

Materials & Construction

Set
No
Stainless
No
Protection Certification
IPX8

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

See all specifications

Description & Specifications

The Gardena 11000 is a powerful and highly efficient clean water drainage pump with an innovative Aquasensor system. Suitable for use in a flooded basement due to rain or for emptying a pool, either in these specific cases or in many other possible scenarios. With this particularly powerful pump, you save energy and it will prove to be an essential addition to your home and garden toolkit.

Extremely efficient thanks to innovative technologies

It has a power of 450 W and pumps up to 11000 liters of clean or slightly dirty water per hour at a pressure of 0.7 bar and a maximum submersion depth of up to 7 m. With a flat suction of just 1 mm, your floor will need a quick wipe for a dry result. This is truly a high-performance and energy-efficient pump

Innovative Aquasensor System

It features modern and innovative characteristics provided by the digital LED Aquasensor. This innovation allows for use in tight spaces, and the pump's activation and deactivation heights can be precisely adjusted with touch control. For example, it can automatically start operating from a water level of just 5 mm - ideal for protecting basements from flooding. The Aquasensor measures the current water level without direct contact and displays the value using a readable LED indicator. 

A useful timer function and an intuitive touch function are also included. The Aquasensor eliminates the risk of dry running, protecting the pump from potential damage. But it is not only the internal functions and self-protective technologies of the GARDENA pump that will impress you.

Powerful, versatile, and efficient

With a maximum depth of 7 m at a pressure of 0.7 bar, the pump is particularly powerful and suitable for various applications. It allows practical flat suction up to 1 mm.

Durable, safe, and completely waterproof

The outer casing is top-notch in terms of durability and design. The stainless steel casing not only looks good but also effectively protects the pump from external damage. The motor shaft has a ceramic coating with triple sealing that includes an oil chamber for even greater durability. Additionally, the drainage pump has an equally useful built-in function for maximum flow rate or dry run shutdown. The user-friendly flow boost switch at the base can push the pump if flat suction is not required to enhance the pump's performance.

Easy GARDENA Hose Connection System

The Drainage Pump 11000 Aquasensor for Clean Water allows the connection of flexible hoses with a diameter of 32 mm (1 ¼ "), 38 mm (1 ½") or 50 mm (2 ") and the connection with a G1 ½ thread for further options.

Specifications

  • Maximum pump submersion: 7m
  • Cable length: 10m
  • Power: 450W
  • Output: 11000 lit/h
  • Maximum head height: 7m
  • Maximum pressure: 0.7 bar
  • Maximum liquid temperature: 35 °C
  • Power cable type: H05 RNF 
  • Electrical protection category: IP X8

Manufacturer

Manufacturer Details

Warnings & Safety Information

Dimensions

Type
Waste Water / Sewage

Type

Waste Water / Sewage

Waste water / sewage pumps are used for pumping and transporting waste water, sewage, and other liquids containing solids or particles
Power Source
Electric

Power Source

Electric
The power supply refers to the pump's need for electrical energy from an external power source, such as single-phase or three-phase power.
Voltage
Single-Phase

Voltage

Single-Phase

Single-phase power supply refers to the provision of electrical energy from single-phase current (e.g., 230V AC), which is the most common type of supply for residential and small commercial applications. 
Horsepower
0.6 hp

Horsepower

Horsepower indicates the kinetic power of the pump. Higher horsepower means more efficiency in water pumping, affecting the flow (l/h) and the head (m).
Power
450 W

Power

It is the energy consumed by the motor to pump water. The greater the power, the more effectively it can lift and move water, especially over long distances or heights.
Cable Length
10 m

Features

Electronic Level Sensor
Yes

Electronic Level Sensor

It automatically activates the pump without the classic hanging float switch. It is ideal for narrow spaces and pits, as there is no risk of it getting stuck anywhere and flooding the area.
with Cutter Impeller
No

with Cutter Impeller

Components that chop, "cut" solid materials, such as organic waste or other particles, before they pass into the pump. They are mainly used in sewage or dirty water pumps, preventing clogging or damage to the system.
Float switch
Yes

Float switch

It is a mechanism that automatically controls the operation of the pump. When the water level reaches a predetermined height, the float activates the pump.
Outlet Nozzle
1/2"

Outlet Nozzle

The outlet nozzle refers to the point or the external diameter of the pump from which the pumped water or liquid exits. It is an important feature for determining the connection of the pump with the piping system and affects the flow capacity of the liquid.
Vortex
No

Vortex

The vortex system in submersible water pumps uses vortex technology to create a rotating water current, which helps in the efficient transfer of water, even when it contains particles or solids.

Pumping Specifications

Maximum Head Height
7 m

Maximum Head Height: 7


The Maximum Head Height refers to the maximum height at which the pump can lift water against resistance (such as pipes or filters). As the head height increases, the pump's flow rate decreases.

  • The maximum head height is considered by manufacturers to be the point where the water will just barely reach.
  • The maximum performance is considered by manufacturers to be the water flow at 0-1 meter head height.
Maximum Output
11 m³/h

Maximum Output

The maximum output or flow of a submersible water pump, as defined by the manufacturers, is the maximum amount of water the pump can move under ideal conditions, usually with zero head (i.e., no lift resistance).
Pump Submersion Depth
7 m
Maximum Particle Size
47.8 mm

Maximum Particle Size

Specifies the largest size of solid particles (such as sand, stones, or other impurities) that the device can pump without clogging or being damaged.
Shallow Suction
Yes

Shallow Suction

This function allows the pump to suck water from an extremely low level (up to 1-3 mm), ideal for flooded floors and basements.

Materials & Construction

Set
No
Stainless
No
Protection Certification
IPX8

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.