For use on broadband COSMOTE TV, excellent. I haven't tried it on anything else since that was the only reason for my purchase.
I didn't read the instructions; within 30 seconds the connection was established without even pressing the pairing buttons on the devices, and the decoder had a picture.
UPDATE1: And for VDSL 50/5 connection, it consistently and without fluctuation achieves 100% of the router's speed. Indicatively, on the well-known Speedtest, 44/4.5.
Some disconnections, especially after waking the computer from sleep mode, are due to the power save mode of the powerlines. You will need to disable it on both devices from the PLC Utility software in the settings. Try it; at least in my case, it solved the problem.
UPDATE2: SOS For those of you who have version 1, and more specifically, it says on the back 1.1, then logically you will have, like me, the factory pre-installed firmware 1.3.0.2134-00_402191_160311_903.
Mistakenly, I went to the TP LINK gr site and downloaded the latest version (or so I thought) for V1, which is 1.1.0.844-01_402011_140208_001. Be careful not to install it because it is, on one hand, older than the factory version by 2 years (2014), and on the other hand, it drops you from 600MBPS to 500MBPS.
So if you make this logical mistake, you will visit the UK site and download the latest firmware version for the 4020P V 1.20 http://uk.tp-link.com/download/TL-PA4020P-KIT-V1.20.html#Firmware. And yet, the factory firmware is version 1.20 and is only available on the UK site. I installed it without any problems and restored the factory firmware version.
για χρήση πάνω σε ευρυζωνικό COSMOTE TV άριστο. Δεν το έχω δοκιμάσει σε κάτι άλλο μιας και αυτός ηταν ο μοναδικός λόγος αγοράς του.
Δεν διάβασα οδηγίες, μέσα σε 30 δεύτερα είχε γίνει η σύνδεση χωρίς να πατήσω καν τα κουμπάκια ζεύξης στις συσκευές και ο αποκωδικοποιητής είχε εικόνα.
UPDATE1: και για σύνδεση vdsl 50/5 πιάνει σταθερά και χωρίς διακύμανση το 100% της ταχύτητας του ρουτερ.
Ενδεικτικά στο γνωστό Speedtest 44/4,5.
Κάποιες αποσυνδέσεις ειδικά μετα απο επαναφορά του υπολογιστή απο sleep mode οφείλονται στο power save mode των powerlines. Θα το απενεργοποιήσετε και στις δύο συσκευές απο το λογισμικό του PLC Utility στις ρυθμίσεις.
Δοκιμάστε το , τουλάχιστον στη δική μου περίπτωση έλυσε το πρόβλημα.
UPDATE2: SOS Για όσους έχετε την έκδοση 1 και πιο συγκεκριμένα γράφει στο πίσω μέρος 1.1 τότε λογικά θα έχετε όπως κι εγώ προεγκατεστημένο το εργοστασιακό firmware 1.3.0.2134-00_402191_160311_903.
Λανθασμένα λοιπόν μπήκα στο site της TP LINK gr και κατέβασα την τελευταία έκδοση (έτσι νόμιζα τουλάχιστον) για την V1 η οποία είναι η
1.1.0.844-01_402011_140208_001
Προσοχή μην την εγκαταστήσετε γιατι είναι αφενός παλιότερη απο την εργοστασιακή κατα 2 χρόνια (2014) και αφετέρου σας ρίχνει απο τα 600MBPS στα 500MBPS..
Εαν λοιπόν κάνετε αυτο το λογικό λάθος θα επισκεφτείτε το site της Αγγλίας και θα κατεβάσετε την τελευταία έκδοση firmware για το 4020P V 1.20
http://uk.tp-link.com/download/TL-PA4020P-KIT-V1.20.html#Firmware
Κι όμως το εργοστασιακό firmware είναι της έκδοσης 1.20 και μάλιστα υπάρχει μόνο στο site της Αγγλίας.
Το εγκατέστησα χωρίς κανένα πρόβλημα και επανέφερα την εργοαστασιακή έκδοση firmware.