Skroutz.mt

Yato Electric burnishing Polisher 1300W with Speed Control and with Suction System YT-81953
Sanders

Yato Electric burnishing Polisher 1300W with Speed Control and with Suction System YT-81953

YATO YT-81953 SATINER 1300W

Device designed for sanding metal and wood. Removes paints (varnishes, colors, stains) or rust without worrying about damaging the surface of the material. The work...

YATO YT-81953 SATINER 1300W

Device designed for sanding metal and wood. Removes paints (varnishes, colors, stains) or rust without worrying about damaging the surface of the material. The work progresses faster than with an angle grinder or wire brush.

The central position of the cylinder on the machine's axis results in symmetrical pressure and uniform...

See full description See full description

  • Power

    Indicates the power of the motor.

    Higher power → stronger material removal and more effective sanding, especially on hard materials.

  • Speed Setting

    Ability to control the rotation speed of the tool.

    1

  • RPM (Revolutions Per Minute)

    • High speeds → fast material removal
    • Low speeds → finer, more controlled finish
  • Reception Diameter 19 mm
  • Weight (Net) 5000 gr
  • See all
Review the product
Product report

Description

Description

YATO YT-81953 SATINER 1300W

Device designed for sanding metal and wood. Removes paints (varnishes, colors, stains) or rust without worrying about damaging the surface of the material. The work progresses faster than with an angle grinder or wire brush.

The central position of the cylinder on the machine's axis results in symmetrical pressure and uniform removal of the coating. The motor and gearbox are resistant to stresses caused by pressing the cylinder onto the workpiece.

The satin cylinder will work well for renovating terraces and aging wood.

Recommended for cleaning:

  • Deck boards
  • Floorboards
  • Boat hull surfaces from rust
  • Asphalt before welding car frame structures

Technical Specifications:

  • Power: 1300 W
  • Work cycle: 900-3700 min⁻¹
  • Voltage: 230 V AC
  • Frequency: 50 Hz
  • Brush diameter: 120 mm
  • Brush width: 100 mm
  • Brush mounting diameter: 19 mm
  • Electronically adjustable speed: Yes
  • Dust extraction system: Yes
  • Cable length: 3 m
  • Electrical insulation class: II
  • Ingress protection: IP20
  • Acoustic pressure: 88.0 ± 3.0 dB(A)
  • Acoustic power: 99.0 ± 3.0 dB(A)
  • Vibrations: 8.85 ± 1.5 m/s²
  • Weight: 5 kg
  • Set contents: satinizer, additional handle, metal brush, nylon brush
  • Application: For processing wooden or metal surfaces, for cleaning painted surfaces, for smoothing the surface

Manufacturer

Manufacturer Details

Warnings & Safety Information
See full description

Specifications

Specifications

Specifications

Type
burnishing Polisher

Type

burnishing Polisher

Tribeio for smoothing mainly metallic surfaces with a rotating grinding head.
Power Source
Electric

Power Source

The method of supplying power to the tool.
Power
1300 W

Power

Indicates the power of the motor.

Higher power → stronger material removal and more effective sanding, especially on hard materials.
Socket Diameter
19 mm
Net Weight
5000 gr
Cable Length
3 m
Palm Sander
No

Palm Sander

Ergonomic sander that can be easily held by hand, without the need for special support or handles.

Features & Functions

Dust Suction System
Yes

Dust Suction System

Used for collecting residues during the operation of the tool.
Speed Setting
Yes

Speed Setting

Ability to control the rotation speed of the tool.
Turns
3700 rpm

Turns

  • High speeds → fast material removal
  • Low speeds → finer, more controlled finish
Noise
3 dB
Brushless
No

Brushless

Motor without brushes, offering greater autonomy and longer lifespan.
Water Supply
No
Soft Start
No

Soft Start

Controls the increase in motor speed when the tool is activated. Instead of starting abruptly at maximum speed, the sander gradually increases its speed over 1–2 seconds.
Brake
No

Brake

Immediately stops the disc when the tool is switched off, for safety and easy abrasive change.
Connection with Vacuum
No

Sandpaper / Belt Specifications

Velcro
No

Velcro

The abrasive pads can be attached with Velcro (hook-and-loop fastener).

Accessories

Carrying Case
Without
Handle Included
No

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

See all specifications

Description & Specifications

YATO YT-81953 SATINER 1300W

Device designed for sanding metal and wood. Removes paints (varnishes, colors, stains) or rust without worrying about damaging the surface of the material. The work progresses faster than with an angle grinder or wire brush.

The central position of the cylinder on the machine's axis results in symmetrical pressure and uniform removal of the coating. The motor and gearbox are resistant to stresses caused by pressing the cylinder onto the workpiece.

The satin cylinder will work well for renovating terraces and aging wood.

Recommended for cleaning:

  • Deck boards
  • Floorboards
  • Boat hull surfaces from rust
  • Asphalt before welding car frame structures

Technical Specifications:

  • Power: 1300 W
  • Work cycle: 900-3700 min⁻¹
  • Voltage: 230 V AC
  • Frequency: 50 Hz
  • Brush diameter: 120 mm
  • Brush width: 100 mm
  • Brush mounting diameter: 19 mm
  • Electronically adjustable speed: Yes
  • Dust extraction system: Yes
  • Cable length: 3 m
  • Electrical insulation class: II
  • Ingress protection: IP20
  • Acoustic pressure: 88.0 ± 3.0 dB(A)
  • Acoustic power: 99.0 ± 3.0 dB(A)
  • Vibrations: 8.85 ± 1.5 m/s²
  • Weight: 5 kg
  • Set contents: satinizer, additional handle, metal brush, nylon brush
  • Application: For processing wooden or metal surfaces, for cleaning painted surfaces, for smoothing the surface

Manufacturer

Manufacturer Details

Warnings & Safety Information

Specifications

Type
burnishing Polisher

Type

burnishing Polisher

Tribeio for smoothing mainly metallic surfaces with a rotating grinding head.
Power Source
Electric

Power Source

The method of supplying power to the tool.
Power
1300 W

Power

Indicates the power of the motor.

Higher power → stronger material removal and more effective sanding, especially on hard materials.
Socket Diameter
19 mm
Net Weight
5000 gr
Cable Length
3 m
Palm Sander
No

Palm Sander

Ergonomic sander that can be easily held by hand, without the need for special support or handles.

Features & Functions

Dust Suction System
Yes

Dust Suction System

Used for collecting residues during the operation of the tool.
Speed Setting
Yes

Speed Setting

Ability to control the rotation speed of the tool.
Turns
3700 rpm

Turns

  • High speeds → fast material removal
  • Low speeds → finer, more controlled finish
Noise
3 dB
Brushless
No

Brushless

Motor without brushes, offering greater autonomy and longer lifespan.
Water Supply
No
Soft Start
No

Soft Start

Controls the increase in motor speed when the tool is activated. Instead of starting abruptly at maximum speed, the sander gradually increases its speed over 1–2 seconds.
Brake
No

Brake

Immediately stops the disc when the tool is switched off, for safety and easy abrasive change.
Connection with Vacuum
No

Sandpaper / Belt Specifications

Velcro
No

Velcro

The abrasive pads can be attached with Velcro (hook-and-loop fastener).

Accessories

Carrying Case
Without
Handle Included
No

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

130,41 €
17,00 €   shipping cost