Skroutz.mt

Zita Brush Zita Pump Pump Waste Water / Sewage 1.73hp 1186100004C23
Submersible Water Pumps

Zita Brush Zita Pump Pump Waste Water / Sewage 1.73hp 1186100004C23

Key features:

  • Power: 1.75 Hp - 1300 Watt
  • Outlet: 2"
  • Maximum flow rate: 18000 lt/h
  • Maximum head: 12m max
  • With Cutter
  • With float switch
See full description

  • Horsepower

    Horsepower indicates the kinetic power of the pump. Higher horsepower means more efficiency in water pumping, affecting the flow (l/h) and the head (m).

  • Power

    It is the energy consumed by the motor to pump water. The greater the power, the more effectively it can lift and move water, especially over long distances or heights.

  • Manometric Height

    12

    The Maximum Head Height refers to the maximum height at which the pump can lift water against resistance (such as pipes or filters). As the head height increases, the pump's flow rate decreases.

    • The maximum head height is considered by manufacturers to be the point where the water will just barely reach.
    • The maximum performance is considered by manufacturers to be the water flow at 0-1 meter head height.
  • See all
This product is temporarily unavailable at Skroutz Last updated: 3 days ago
Review the product
Product report

Description

Description

Capabilities

Single-phase sewage pump 1.75Hp, ideal for managing urban sewage, emptying cesspools and septic tanks. Also suitable for small rental room units-hotels, handling industrial and agricultural waste, suitable for sewage in factories, use in construction sites and commercial facilities. Sewage pump of excellent quality with a specially constructed motor with 100% copper winding for greater durability and longevity, new type sewage pump with cutter and float - stainless steel body - cast iron pump body and impeller, the pump body and impeller are made of cast iron.

Specifications

  • Power: 1.75 Hp - 1300 Watt
  • Voltage: 220V/50Hz
  • Outlet: 2"
  • Motor body, impeller, pump shaft made of AISI 304
  • Material: Cast iron pump body - stainless steel
  • Shaft core: Stainless steel
  • Maximum flow rate: 18000 lt/h
  • Maximum head: 12m max
  • Maximum submersion capacity: 5.0 m
  • With Cutter
  • Maximum water temperature: +40°C
  • Copper winding (for longer duration and durability)
  • Built-in thermal protection
  • With float switch
  • Two-channel impeller. Fixed cutting blade. (High-efficiency spiral cutting impeller)
  • Sealing with mechanical seal SiC+ Graphite / Ceramic + Graphite
  • Protection rating: IP X8
  • Insulation class: F
  • Dimensions: 45 cm (height) x 33.0 cm
  • Weight: 20.0kg
  • Type: V-1300DF

Manufacturer

Manufacturer Details

Warnings & Safety Information
See full description

Specifications

Specifications

Dimensions

Type
Waste Water / Sewage

Type

Waste Water / Sewage

Waste water / sewage pumps are used for pumping and transporting waste water, sewage, and other liquids containing solids or particles
Power Source
Electric

Power Source

Electric
The power supply refers to the pump's need for electrical energy from an external power source, such as single-phase or three-phase power.
Horsepower
1.73 hp

Horsepower

Horsepower indicates the kinetic power of the pump. Higher horsepower means more efficiency in water pumping, affecting the flow (l/h) and the head (m).
Power
1297.5 W

Power

It is the energy consumed by the motor to pump water. The greater the power, the more effectively it can lift and move water, especially over long distances or heights.
Cable Length
12 m

Features

Electronic Level Sensor
No

Electronic Level Sensor

It automatically activates the pump without the classic hanging float switch. It is ideal for narrow spaces and pits, as there is no risk of it getting stuck anywhere and flooding the area.
with Cutter Impeller
Yes

with Cutter Impeller

Components that chop, "cut" solid materials, such as organic waste or other particles, before they pass into the pump. They are mainly used in sewage or dirty water pumps, preventing clogging or damage to the system.
Float switch
Yes

Float switch

It is a mechanism that automatically controls the operation of the pump. When the water level reaches a predetermined height, the float activates the pump.
Outlet Nozzle
2"

Outlet Nozzle

The outlet nozzle refers to the point or the external diameter of the pump from which the pumped water or liquid exits. It is an important feature for determining the connection of the pump with the piping system and affects the flow capacity of the liquid.
Vortex
No

Vortex

The vortex system in submersible water pumps uses vortex technology to create a rotating water current, which helps in the efficient transfer of water, even when it contains particles or solids.

Pumping Specifications

Maximum Head Height
12 m

Maximum Head Height: 12


The Maximum Head Height refers to the maximum height at which the pump can lift water against resistance (such as pipes or filters). As the head height increases, the pump's flow rate decreases.

  • The maximum head height is considered by manufacturers to be the point where the water will just barely reach.
  • The maximum performance is considered by manufacturers to be the water flow at 0-1 meter head height.
Maximum Output
18 m³/h

Maximum Output

The maximum output or flow of a submersible water pump, as defined by the manufacturers, is the maximum amount of water the pump can move under ideal conditions, usually with zero head (i.e., no lift resistance).
Pump Submersion Depth
5 m
Shallow Suction
No

Shallow Suction

This function allows the pump to suck water from an extremely low level (up to 1-3 mm), ideal for flooded floors and basements.

Materials & Construction

Set
No
Stainless
Yes
Protection Certification
IPX8

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

See all specifications

Description & Specifications

Capabilities

Single-phase sewage pump 1.75Hp, ideal for managing urban sewage, emptying cesspools and septic tanks. Also suitable for small rental room units-hotels, handling industrial and agricultural waste, suitable for sewage in factories, use in construction sites and commercial facilities. Sewage pump of excellent quality with a specially constructed motor with 100% copper winding for greater durability and longevity, new type sewage pump with cutter and float - stainless steel body - cast iron pump body and impeller, the pump body and impeller are made of cast iron.

Specifications

  • Power: 1.75 Hp - 1300 Watt
  • Voltage: 220V/50Hz
  • Outlet: 2"
  • Motor body, impeller, pump shaft made of AISI 304
  • Material: Cast iron pump body - stainless steel
  • Shaft core: Stainless steel
  • Maximum flow rate: 18000 lt/h
  • Maximum head: 12m max
  • Maximum submersion capacity: 5.0 m
  • With Cutter
  • Maximum water temperature: +40°C
  • Copper winding (for longer duration and durability)
  • Built-in thermal protection
  • With float switch
  • Two-channel impeller. Fixed cutting blade. (High-efficiency spiral cutting impeller)
  • Sealing with mechanical seal SiC+ Graphite / Ceramic + Graphite
  • Protection rating: IP X8
  • Insulation class: F
  • Dimensions: 45 cm (height) x 33.0 cm
  • Weight: 20.0kg
  • Type: V-1300DF

Manufacturer

Manufacturer Details

Warnings & Safety Information

Dimensions

Type
Waste Water / Sewage

Type

Waste Water / Sewage

Waste water / sewage pumps are used for pumping and transporting waste water, sewage, and other liquids containing solids or particles
Power Source
Electric

Power Source

Electric
The power supply refers to the pump's need for electrical energy from an external power source, such as single-phase or three-phase power.
Horsepower
1.73 hp

Horsepower

Horsepower indicates the kinetic power of the pump. Higher horsepower means more efficiency in water pumping, affecting the flow (l/h) and the head (m).
Power
1297.5 W

Power

It is the energy consumed by the motor to pump water. The greater the power, the more effectively it can lift and move water, especially over long distances or heights.
Cable Length
12 m

Features

Electronic Level Sensor
No

Electronic Level Sensor

It automatically activates the pump without the classic hanging float switch. It is ideal for narrow spaces and pits, as there is no risk of it getting stuck anywhere and flooding the area.
with Cutter Impeller
Yes

with Cutter Impeller

Components that chop, "cut" solid materials, such as organic waste or other particles, before they pass into the pump. They are mainly used in sewage or dirty water pumps, preventing clogging or damage to the system.
Float switch
Yes

Float switch

It is a mechanism that automatically controls the operation of the pump. When the water level reaches a predetermined height, the float activates the pump.
Outlet Nozzle
2"

Outlet Nozzle

The outlet nozzle refers to the point or the external diameter of the pump from which the pumped water or liquid exits. It is an important feature for determining the connection of the pump with the piping system and affects the flow capacity of the liquid.
Vortex
No

Vortex

The vortex system in submersible water pumps uses vortex technology to create a rotating water current, which helps in the efficient transfer of water, even when it contains particles or solids.

Pumping Specifications

Maximum Head Height
12 m

Maximum Head Height: 12


The Maximum Head Height refers to the maximum height at which the pump can lift water against resistance (such as pipes or filters). As the head height increases, the pump's flow rate decreases.

  • The maximum head height is considered by manufacturers to be the point where the water will just barely reach.
  • The maximum performance is considered by manufacturers to be the water flow at 0-1 meter head height.
Maximum Output
18 m³/h

Maximum Output

The maximum output or flow of a submersible water pump, as defined by the manufacturers, is the maximum amount of water the pump can move under ideal conditions, usually with zero head (i.e., no lift resistance).
Pump Submersion Depth
5 m
Shallow Suction
No

Shallow Suction

This function allows the pump to suck water from an extremely low level (up to 1-3 mm), ideal for flooded floors and basements.

Materials & Construction

Set
No
Stainless
Yes
Protection Certification
IPX8

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.