Skroutz.mt

Imperia PLC 46 Plasma Cutting Inverter 40A
Welding Machines

Imperia PLC 46 Plasma Cutting Inverter 40A

IMPERIA - PLC 46 Plasma Metal Cutting Inverter

Features:

  • Performance@ 25% / 40C (KVA): 4.9
  • Cutting Current (A): 20-40
  • Cutting Thickness (mm): 12 (max)
  • Weight: 8.6kg
  • Voltage (V): 230
  • Ergo Cut S45...

IMPERIA - PLC 46 Plasma Metal Cutting Inverter

Features:

  • Performance@ 25% / 40C (KVA): 4.9
  • Cutting Current (A): 20-40
  • Cutting Thickness (mm): 12 (max)
  • Weight: 8.6kg
  • Voltage (V): 230
  • Ergo Cut S45 torch with 6m length
  • Cable with grounding clamp
  • Air regulator
  • No High Frequency

Description:

New technology plasma with top-notch next-generation electronics....

See full description See full description

  • Welding Current

    40

    Suitable for use on thin sheets and DIY constructions.

  • Duty Cycle

    The Duty Cycle is the portion of a ten-minute period that a welding machine can operate continuously at maximum Amperes before it needs to stop and cool down.

    2.

    For example, a welding machine with a maximum Amperage of 200 A and a Duty Cycle of 30% can operate continuously at 200 A for 3 minutes before it needs to stop.

  • Power Supply Voltage

    230

    It is the supply voltage that the machine requires from the electrical grid.

  • Power

    4.9

    Affects the power consumption of the machine and determines if it can be supported by the electrical network you are using.
  • See all
Product report

Description

Description

IMPERIA - PLC 46 Plasma Metal Cutting Inverter

Features:

  • Performance@ 25% / 40C (KVA): 4.9
  • Cutting Current (A): 20-40
  • Cutting Thickness (mm): 12 (max)
  • Weight: 8.6kg
  • Voltage (V): 230
  • Ergo Cut S45 torch with 6m length
  • Cable with grounding clamp
  • Air regulator
  • No High Frequency

Description:

New technology plasma with top-notch next-generation electronics. Excellent performance, low power consumption, ease and safety of use are some of the special features of the PLC 46 plasma metal cutting machine. Suitable for cutting stainless steel, copper, aluminum, and steel.

Manufacturer

Manufacturer Details

Warnings & Safety Information
See full description

Specifications

Specifications

Dimensions

Type
Plasma Cutting

Type

Plasma Cutting

It uses compressed air to cut almost any type of metal with speed and precision. At 50A, it can cut metal up to 2.5cm thick. 2. It is mainly used by specialized personnel in workshops (e.g. car repairs).
Welding Current (max)
40 A

Welding Current (max): 40


Suitable for use on thin sheets and DIY constructions.
Operation Cycle (max Ampere)
25 %

Operation Cycle (max Ampere)

The Duty Cycle is the portion of a ten-minute period that a welding machine can operate continuously at maximum Amperes before it needs to stop and cool down.

2.

For example, a welding machine with a maximum Amperage of 200 A and a Duty Cycle of 30% can operate continuously at 200 A for 3 minutes before it needs to stop.
Supply Voltage
230 V

Supply Voltage: 230


It is the supply voltage that the machine requires from the electrical grid.
Power
4.9 kVA

Power: 4.9


Affects the power consumption of the machine and determines if it can be supported by the electrical network you are using.
Weight
8600 gr

Additional Features

Inverter
Yes

Inverter


New technology welding. Very good in terms of performance, durability, and weight, but with a high cost of repair in case of damage. They have automation for better and safer work. If connected to a generator, it is recommended to choose one with 8kVA or more.
IGBT
Yes

IGBT


Allows the conversion of direct current (DC) voltage to alternating current (AC) or the output of direct current at a higher or lower intensity.
VRD
No
with Voltage Stabilizer
No
for Generator with AVR
Yes

for Generator with AVR


Suitable for generator with AVR voltage stabilizer.

Features

Hot Start
No
Anti Stick
No
Arc Force
No
2T Operation
No
4T Mode
No
Spot Function
No
Pulsed
No

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

See all specifications

Reviews (1)

Reviews

4.0
1
4.0
Review this product
  1. 5 stars
    0
  2. 1
  3. 3 stars
    0
  4. 2 stars
    0
  5. 1 star
    0
Review this product

Reviews by our members

  • kokkinidisdim
    4
    3 out of 3 members found this review helpful
    kokkinidisdim

    I have it since 2014, it works fine, no problems until now, but I struggle to cut anything thicker than 8 millimeters, it takes a long time, for the 14 millimeters they claim it's quite difficult, it will cut them but the cut is not clean, but I rarely cut something that thick, I work with it up to 4 millimeters inox and I am satisfied, I wouldn't buy it again, I would get a bigger one in terms of amperage, and the consumables are very expensive, the nozzles and electrodes, but I bought them from eBay, 100 pairs for 40€, here they were 10€ per pair at that time.

    Translated from Greek ·
    • Machine durability
    • Construction quality
    • Weight
    • Volume
    • Easy to use
    • Welding cable length
    • Value for money
    • Power
    Did you find this review helpful?
  • kokkinidisdim
    4
    kokkinidisdim

    I have it since 2014, it works fine, no problems until now, but I struggle to cut anything thicker than 8 millimeters, it takes a long time, for the 14 millimeters they claim it's quite difficult, it will cut them but the cut is not clean, but I rarely cut something that thick, I work with it up to 4 millimeters inox and I am satisfied, I wouldn't buy it again, I would get a bigger one in terms of amperage, and the consumables are very expensive, the nozzles and electrodes, but I bought them from eBay, 100 pairs for 40€, here they were 10€ per pair at that time.

    Translated from Greek ·
    3
  • See all

Description & Specifications

IMPERIA - PLC 46 Plasma Metal Cutting Inverter

Features:

  • Performance@ 25% / 40C (KVA): 4.9
  • Cutting Current (A): 20-40
  • Cutting Thickness (mm): 12 (max)
  • Weight: 8.6kg
  • Voltage (V): 230
  • Ergo Cut S45 torch with 6m length
  • Cable with grounding clamp
  • Air regulator
  • No High Frequency

Description:

New technology plasma with top-notch next-generation electronics. Excellent performance, low power consumption, ease and safety of use are some of the special features of the PLC 46 plasma metal cutting machine. Suitable for cutting stainless steel, copper, aluminum, and steel.

Manufacturer

Manufacturer Details

Warnings & Safety Information

Dimensions

Type
Plasma Cutting

Type

Plasma Cutting

It uses compressed air to cut almost any type of metal with speed and precision. At 50A, it can cut metal up to 2.5cm thick. 2. It is mainly used by specialized personnel in workshops (e.g. car repairs).
Welding Current (max)
40 A

Welding Current (max): 40


Suitable for use on thin sheets and DIY constructions.
Operation Cycle (max Ampere)
25 %

Operation Cycle (max Ampere)

The Duty Cycle is the portion of a ten-minute period that a welding machine can operate continuously at maximum Amperes before it needs to stop and cool down.

2.

For example, a welding machine with a maximum Amperage of 200 A and a Duty Cycle of 30% can operate continuously at 200 A for 3 minutes before it needs to stop.
Supply Voltage
230 V

Supply Voltage: 230


It is the supply voltage that the machine requires from the electrical grid.
Power
4.9 kVA

Power: 4.9


Affects the power consumption of the machine and determines if it can be supported by the electrical network you are using.
Weight
8600 gr

Additional Features

Inverter
Yes

Inverter


New technology welding. Very good in terms of performance, durability, and weight, but with a high cost of repair in case of damage. They have automation for better and safer work. If connected to a generator, it is recommended to choose one with 8kVA or more.
IGBT
Yes

IGBT


Allows the conversion of direct current (DC) voltage to alternating current (AC) or the output of direct current at a higher or lower intensity.
VRD
No
with Voltage Stabilizer
No
for Generator with AVR
Yes

for Generator with AVR


Suitable for generator with AVR voltage stabilizer.

Features

Hot Start
No
Anti Stick
No
Arc Force
No
2T Operation
No
4T Mode
No
Spot Function
No
Pulsed
No

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

Reviews (1)

4.0
1
4.0
Review this product
  1. 5 stars
    0
  2. 1
  3. 3 stars
    0
  4. 2 stars
    0
  5. 1 star
    0
Review this product

Reviews by our members

  • kokkinidisdim
    4
    3 out of 3 members found this review helpful
    kokkinidisdim

    I have it since 2014, it works fine, no problems until now, but I struggle to cut anything thicker than 8 millimeters, it takes a long time, for the 14 millimeters they claim it's quite difficult, it will cut them but the cut is not clean, but I rarely cut something that thick, I work with it up to 4 millimeters inox and I am satisfied, I wouldn't buy it again, I would get a bigger one in terms of amperage, and the consumables are very expensive, the nozzles and electrodes, but I bought them from eBay, 100 pairs for 40€, here they were 10€ per pair at that time.

    Translated from Greek ·
    • Machine durability
    • Construction quality
    • Weight
    • Volume
    • Easy to use
    • Welding cable length
    • Value for money
    • Power
    Did you find this review helpful?
  • kokkinidisdim
    4
    kokkinidisdim

    I have it since 2014, it works fine, no problems until now, but I struggle to cut anything thicker than 8 millimeters, it takes a long time, for the 14 millimeters they claim it's quite difficult, it will cut them but the cut is not clean, but I rarely cut something that thick, I work with it up to 4 millimeters inox and I am satisfied, I wouldn't buy it again, I would get a bigger one in terms of amperage, and the consumables are very expensive, the nozzles and electrodes, but I bought them from eBay, 100 pairs for 40€, here they were 10€ per pair at that time.

    Translated from Greek ·
    3
  • See all
629,00 €
44,00 €   shipping cost