The Peladn S-1 eGPU docking station connects to a computer via Thunderbolt 3 and supports an external graphics card, enhancing the system’s graphics processing capabilities. Its open design makes it...
The Peladn S-1 eGPU docking station connects to a computer via Thunderbolt 3 and supports an external graphics card, enhancing the system’s graphics processing capabilities. Its open design makes it easy to install and upgrade components while helping dissipate heat. It also features an M.2 NVMe slot and a Gigabit Ethernet port.
The Peladn S-1 eGPU docking station connects to a computer via Thunderbolt 3 and supports an external graphics card, enhancing the system’s graphics processing capabilities. Its open design makes it easy to install and upgrade components while helping dissipate heat. It also features an M.2 NVMe slot and a Gigabit Ethernet port.
The dock supports ATX and SFX power supplies, sold separately, as well as most graphics cards on the market. An ATX 3.0 power supply is required for NVIDIA RTX 40 graphics cards.
Interface: 2 Thunderbolt 3 ports (60 W + 15 W)
Bandwidth: 40 Gb/s
Network port: 1 Gigabit Ethernet 1000M port
Drive slot: 1 M.2 2280 NVMe slot, up to 2 TB
Supported power supplies: ATX and SFX
Supported graphics cards: Most available models
Recommended AMD graphics cards: RX570 or newer
Recommended NVIDIA graphics cards: GTX1060 or newer
NVIDIA RTX 40 support: With an ATX 3.0 power supply
AMD RX 7000 support: Yes
System requirements: Windows 10 64-bit or macOS 10.13.4 or later for AMD graphics cards
Computer requirements: Thunderbolt 3 port with eGPU support
Dimensions: 253 x 162 x 41 mm
Package contents: eGPU docking station, USB 4.0 cable, screwdriver, and installation manual
Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.
GeForce RTX5070ti works with this dock and my Lenovo P1 gen4. Sometimes I see micro freezes, two or three times during the two weeks I'm using it I had eGPU suddenly disconnnected during a game, but still it is much better experience than trying to play games on a laptop's weak so-called "dedicated" graphics card.
What could be better:
- The dock has mounting holes only on a front side, and they are not enough to firmly attach ATX power supply and GPU to the dock. I mean its Ok while everything is standing on a table, but have to be very cautious moving things around. My RTX5070ti has embedded nuts on its back side and it would be great to have them in the dock's back too, but alas.
- the NVMe bay is not convenient to use
- the GPU coolers keep spinning when the dock is disconnected from the laptop. So I have to switch off the dock's power supply each time I shut down the laptop.
Now some troubleshooting notes for those who may use the dock with a laptop similar to mine:
My laptop has an RTX A2000 built in and that made drivers setup troublesome: Lenovo driver for A2000 does not have RTX5070 in the list of supported hardware, gaming drivers do not list the A2000 and its impossible to install them both at the same time. The solution was to use NVCleanstall utility to add extra VID/PID to one of those drivers' list of supported hardware (I ended up using the Studio driver).
Another issue with my laptop was that after eGPU drivers installation it kept hanging before Windows boot up each time I boot with eGPU disconnected. This was fixed by switching from "Dedicated graphics" to "Hybrid graphics" mode in BIOS setup.
GeForce RTX5070ti works with this dock and my Lenovo P1 gen4. Sometimes I see micro freezes, two or three times during the two weeks I'm using it I had eGPU suddenly disconnnected during a game, but still it is much better experience than trying to play games on a laptop's weak so-called "dedicated" graphics card.
What could be better:
- The dock has mounting holes only on a front side, and they are not enough to firmly attach ATX power supply and GPU to the dock. I mean its Ok while everything is standing on a table, but have to be very cautious moving things around. My RTX5070ti has embedded nuts on its back side and it would be great to have them in the dock's back too, but alas.
- the NVMe bay is not convenient to use
- the GPU coolers keep spinning when the dock is disconnected from the laptop. So I have to switch off the dock's power supply each time I shut down the laptop.
Now some troubleshooting notes for those who may use the dock with a laptop similar to mine:
My laptop has an RTX A2000 built in and that made drivers setup troublesome: Lenovo driver for A2000 does not have RTX5070 in the list of supported hardware, gaming drivers do not list the A2000 and its impossible to install them both at the same time. The solution was to use NVCleanstall utility to add extra VID/PID to one of those drivers' list of supported hardware (I ended up using the Studio driver).
Another issue with my laptop was that after eGPU drivers installation it kept hanging before Windows boot up each time I boot with eGPU disconnected. This was fixed by switching from "Dedicated graphics" to "Hybrid graphics" mode in BIOS setup.
GeForce RTX5070ti works with this dock and my Lenovo P1 gen4. Sometimes I see micro freezes, two or three times during the two weeks I'm using it I had eGPU suddenly disconnnected during a game, but still it is much better experience than trying to play games on a laptop's weak so-called "dedicated" graphics card.
What could be better:
- The dock has mounting holes only on a front side, and they are not enough to firmly attach ATX power supply and GPU to the dock. I mean its Ok while everything is standing on a table, but have to be very cautious moving things around. My RTX5070ti has embedded nuts on its back side and it would be great to have them in the dock's back too, but alas.
- the NVMe bay is not convenient to use
- the GPU coolers keep spinning when the dock is disconnected from the laptop. So I have to switch off the dock's power supply each time I shut down the laptop.
Now some troubleshooting notes for those who may use the dock with a laptop similar to mine:
My laptop has an RTX A2000 built in and that made drivers setup troublesome: Lenovo driver for A2000 does not have RTX5070 in the list of supported hardware, gaming drivers do not list the A2000 and its impossible to install them both at the same time. The solution was to use NVCleanstall utility to add extra VID/PID to one of those drivers' list of supported hardware (I ended up using the Studio driver).
Another issue with my laptop was that after eGPU drivers installation it kept hanging before Windows boot up each time I boot with eGPU disconnected. This was fixed by switching from "Dedicated graphics" to "Hybrid graphics" mode in BIOS setup.
GeForce RTX5070ti works with this dock and my Lenovo P1 gen4. Sometimes I see micro freezes, two or three times during the two weeks I'm using it I had eGPU suddenly disconnnected during a game, but still it is much better experience than trying to play games on a laptop's weak so-called "dedicated" graphics card.
What could be better:
- The dock has mounting holes only on a front side, and they are not enough to firmly attach ATX power supply and GPU to the dock. I mean its Ok while everything is standing on a table, but have to be very cautious moving things around. My RTX5070ti has embedded nuts on its back side and it would be great to have them in the dock's back too, but alas.
- the NVMe bay is not convenient to use
- the GPU coolers keep spinning when the dock is disconnected from the laptop. So I have to switch off the dock's power supply each time I shut down the laptop.
Now some troubleshooting notes for those who may use the dock with a laptop similar to mine:
My laptop has an RTX A2000 built in and that made drivers setup troublesome: Lenovo driver for A2000 does not have RTX5070 in the list of supported hardware, gaming drivers do not list the A2000 and its impossible to install them both at the same time. The solution was to use NVCleanstall utility to add extra VID/PID to one of those drivers' list of supported hardware (I ended up using the Studio driver).
Another issue with my laptop was that after eGPU drivers installation it kept hanging before Windows boot up each time I boot with eGPU disconnected. This was fixed by switching from "Dedicated graphics" to "Hybrid graphics" mode in BIOS setup.
The Peladn S-1 eGPU docking station connects to a computer via Thunderbolt 3 and supports an external graphics card, enhancing the system’s graphics processing capabilities. Its open design makes it easy to install and upgrade components while helping dissipate heat. It also features an M.2 NVMe slot and a Gigabit Ethernet port.
The dock supports ATX and SFX power supplies, sold separately, as well as most graphics cards on the market. An ATX 3.0 power supply is required for NVIDIA RTX 40 graphics cards.
Interface: 2 Thunderbolt 3 ports (60 W + 15 W)
Bandwidth: 40 Gb/s
Network port: 1 Gigabit Ethernet 1000M port
Drive slot: 1 M.2 2280 NVMe slot, up to 2 TB
Supported power supplies: ATX and SFX
Supported graphics cards: Most available models
Recommended AMD graphics cards: RX570 or newer
Recommended NVIDIA graphics cards: GTX1060 or newer
NVIDIA RTX 40 support: With an ATX 3.0 power supply
AMD RX 7000 support: Yes
System requirements: Windows 10 64-bit or macOS 10.13.4 or later for AMD graphics cards
Computer requirements: Thunderbolt 3 port with eGPU support
Dimensions: 253 x 162 x 41 mm
Package contents: eGPU docking station, USB 4.0 cable, screwdriver, and installation manual
Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.
GeForce RTX5070ti works with this dock and my Lenovo P1 gen4. Sometimes I see micro freezes, two or three times during the two weeks I'm using it I had eGPU suddenly disconnnected during a game, but still it is much better experience than trying to play games on a laptop's weak so-called "dedicated" graphics card.
What could be better:
- The dock has mounting holes only on a front side, and they are not enough to firmly attach ATX power supply and GPU to the dock. I mean its Ok while everything is standing on a table, but have to be very cautious moving things around. My RTX5070ti has embedded nuts on its back side and it would be great to have them in the dock's back too, but alas.
- the NVMe bay is not convenient to use
- the GPU coolers keep spinning when the dock is disconnected from the laptop. So I have to switch off the dock's power supply each time I shut down the laptop.
Now some troubleshooting notes for those who may use the dock with a laptop similar to mine:
My laptop has an RTX A2000 built in and that made drivers setup troublesome: Lenovo driver for A2000 does not have RTX5070 in the list of supported hardware, gaming drivers do not list the A2000 and its impossible to install them both at the same time. The solution was to use NVCleanstall utility to add extra VID/PID to one of those drivers' list of supported hardware (I ended up using the Studio driver).
Another issue with my laptop was that after eGPU drivers installation it kept hanging before Windows boot up each time I boot with eGPU disconnected. This was fixed by switching from "Dedicated graphics" to "Hybrid graphics" mode in BIOS setup.
GeForce RTX5070ti works with this dock and my Lenovo P1 gen4. Sometimes I see micro freezes, two or three times during the two weeks I'm using it I had eGPU suddenly disconnnected during a game, but still it is much better experience than trying to play games on a laptop's weak so-called "dedicated" graphics card.
What could be better:
- The dock has mounting holes only on a front side, and they are not enough to firmly attach ATX power supply and GPU to the dock. I mean its Ok while everything is standing on a table, but have to be very cautious moving things around. My RTX5070ti has embedded nuts on its back side and it would be great to have them in the dock's back too, but alas.
- the NVMe bay is not convenient to use
- the GPU coolers keep spinning when the dock is disconnected from the laptop. So I have to switch off the dock's power supply each time I shut down the laptop.
Now some troubleshooting notes for those who may use the dock with a laptop similar to mine:
My laptop has an RTX A2000 built in and that made drivers setup troublesome: Lenovo driver for A2000 does not have RTX5070 in the list of supported hardware, gaming drivers do not list the A2000 and its impossible to install them both at the same time. The solution was to use NVCleanstall utility to add extra VID/PID to one of those drivers' list of supported hardware (I ended up using the Studio driver).
Another issue with my laptop was that after eGPU drivers installation it kept hanging before Windows boot up each time I boot with eGPU disconnected. This was fixed by switching from "Dedicated graphics" to "Hybrid graphics" mode in BIOS setup.
GeForce RTX5070ti works with this dock and my Lenovo P1 gen4. Sometimes I see micro freezes, two or three times during the two weeks I'm using it I had eGPU suddenly disconnnected during a game, but still it is much better experience than trying to play games on a laptop's weak so-called "dedicated" graphics card.
What could be better:
- The dock has mounting holes only on a front side, and they are not enough to firmly attach ATX power supply and GPU to the dock. I mean its Ok while everything is standing on a table, but have to be very cautious moving things around. My RTX5070ti has embedded nuts on its back side and it would be great to have them in the dock's back too, but alas.
- the NVMe bay is not convenient to use
- the GPU coolers keep spinning when the dock is disconnected from the laptop. So I have to switch off the dock's power supply each time I shut down the laptop.
Now some troubleshooting notes for those who may use the dock with a laptop similar to mine:
My laptop has an RTX A2000 built in and that made drivers setup troublesome: Lenovo driver for A2000 does not have RTX5070 in the list of supported hardware, gaming drivers do not list the A2000 and its impossible to install them both at the same time. The solution was to use NVCleanstall utility to add extra VID/PID to one of those drivers' list of supported hardware (I ended up using the Studio driver).
Another issue with my laptop was that after eGPU drivers installation it kept hanging before Windows boot up each time I boot with eGPU disconnected. This was fixed by switching from "Dedicated graphics" to "Hybrid graphics" mode in BIOS setup.
GeForce RTX5070ti works with this dock and my Lenovo P1 gen4. Sometimes I see micro freezes, two or three times during the two weeks I'm using it I had eGPU suddenly disconnnected during a game, but still it is much better experience than trying to play games on a laptop's weak so-called "dedicated" graphics card.
What could be better:
- The dock has mounting holes only on a front side, and they are not enough to firmly attach ATX power supply and GPU to the dock. I mean its Ok while everything is standing on a table, but have to be very cautious moving things around. My RTX5070ti has embedded nuts on its back side and it would be great to have them in the dock's back too, but alas.
- the NVMe bay is not convenient to use
- the GPU coolers keep spinning when the dock is disconnected from the laptop. So I have to switch off the dock's power supply each time I shut down the laptop.
Now some troubleshooting notes for those who may use the dock with a laptop similar to mine:
My laptop has an RTX A2000 built in and that made drivers setup troublesome: Lenovo driver for A2000 does not have RTX5070 in the list of supported hardware, gaming drivers do not list the A2000 and its impossible to install them both at the same time. The solution was to use NVCleanstall utility to add extra VID/PID to one of those drivers' list of supported hardware (I ended up using the Studio driver).
Another issue with my laptop was that after eGPU drivers installation it kept hanging before Windows boot up each time I boot with eGPU disconnected. This was fixed by switching from "Dedicated graphics" to "Hybrid graphics" mode in BIOS setup.