Skroutz.mt

Maverick Waste Water and Rainwater Pump 750W KR-MAV-MV138
Submersible Water Pumps

Maverick Waste Water and Rainwater Pump 750W KR-MAV-MV138

Key features:

  • Stainless steel impeller and shaft
  • Maximum flow rate 12,500 lt/h
  • Solids passage up to 35mm
  • Maximum submersion depth 7m

With the advanced stainless steel impeller of the Maverick MV138, you tackle any flooded area with absolute speed and safety.

See full description

  • Power

    It is the energy consumed by the motor to pump water. The greater the power, the more effectively it can lift and move water, especially over long distances or heights.

  • Manometric Height

    8

    The Maximum Head Height refers to the maximum height at which the pump can lift water against resistance (such as pipes or filters). As the head height increases, the pump's flow rate decreases.

    • The maximum head height is considered by manufacturers to be the point where the water will just barely reach.
    • The maximum performance is considered by manufacturers to be the water flow at 0-1 meter head height.
  • See all
The product is not available for shipping to the selected country.
Review the product
Product report

Description

Description

At a glance

  • Stainless steel impeller and shaft: Ensure top corrosion resistance and long-term reliability even under continuous use in demanding environments.
  • Maximum flow rate 12,500 lt/h: Provides exceptionally fast water drainage from basements, shafts, and flooded areas without delays.
  • Passage of solids up to 35mm: Allows unobstructed pumping of dirty and rainwater with debris, minimizing the risk of clogging.
  • Maximum submersion depth 7m: Ensures pump operation even in deep tanks, cisterns, or deep collection shafts.

Ultimate Corrosion Resistance

Forget once and for all about the damage caused by stagnant water. Thanks to the stainless steel impeller and reinforced shaft, the Maverick MV138 pump performs exceptionally well in corrosive or sandy environments. You can rely on it for continuous and demanding use, knowing that its internal parts are fully protected, offering you top durability.

Technical Specifications

  • Type: Submersible pump for sewage & rainwater
  • Power: 750 W
  • Maximum Flow Rate (Qmax): 12,500 lt/h
  • Maximum Head (Hmax): 8.0 m
  • Maximum Submersion Depth: 7.0 m
  • Maximum Solid Passage: 35 mm
  • Impeller / Shaft Material: Stainless steel
  • Suitable for: Basements, pits, tanks, excavations, flooded areas, and irrigation from troughs or cisterns

Manufacturer

Manufacturer Details

Warnings & Safety Information
See full description

Specifications

Specifications

Dimensions

Type
Waste Water / Sewage, Rainwater

Type

Waste Water / Sewage

Waste water / sewage pumps are used for pumping and transporting waste water, sewage, and other liquids containing solids or particles
Power Source
Electric

Power Source

Electric
The power supply refers to the pump's need for electrical energy from an external power source, such as single-phase or three-phase power.
Power
750 W

Power

It is the energy consumed by the motor to pump water. The greater the power, the more effectively it can lift and move water, especially over long distances or heights.

Features

Electronic Level Sensor
No

Electronic Level Sensor

It automatically activates the pump without the classic hanging float switch. It is ideal for narrow spaces and pits, as there is no risk of it getting stuck anywhere and flooding the area.
with Cutter Impeller
No

with Cutter Impeller

Components that chop, "cut" solid materials, such as organic waste or other particles, before they pass into the pump. They are mainly used in sewage or dirty water pumps, preventing clogging or damage to the system.
Float switch
No

Float switch

It is a mechanism that automatically controls the operation of the pump. When the water level reaches a predetermined height, the float activates the pump.
Vortex
No

Vortex

The vortex system in submersible water pumps uses vortex technology to create a rotating water current, which helps in the efficient transfer of water, even when it contains particles or solids.

Pumping Specifications

Maximum Head Height
8 m

Maximum Head Height: 8


The Maximum Head Height refers to the maximum height at which the pump can lift water against resistance (such as pipes or filters). As the head height increases, the pump's flow rate decreases.

  • The maximum head height is considered by manufacturers to be the point where the water will just barely reach.
  • The maximum performance is considered by manufacturers to be the water flow at 0-1 meter head height.
Maximum Output
12 m³/h

Maximum Output

The maximum output or flow of a submersible water pump, as defined by the manufacturers, is the maximum amount of water the pump can move under ideal conditions, usually with zero head (i.e., no lift resistance).
Maximum Particle Size
35 mm

Maximum Particle Size

Specifies the largest size of solid particles (such as sand, stones, or other impurities) that the device can pump without clogging or being damaged.
Shallow Suction
No

Shallow Suction

This function allows the pump to suck water from an extremely low level (up to 1-3 mm), ideal for flooded floors and basements.

Materials & Construction

Set
No
Stainless
Yes

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

See all specifications

Description & Specifications

At a glance

  • Stainless steel impeller and shaft: Ensure top corrosion resistance and long-term reliability even under continuous use in demanding environments.
  • Maximum flow rate 12,500 lt/h: Provides exceptionally fast water drainage from basements, shafts, and flooded areas without delays.
  • Passage of solids up to 35mm: Allows unobstructed pumping of dirty and rainwater with debris, minimizing the risk of clogging.
  • Maximum submersion depth 7m: Ensures pump operation even in deep tanks, cisterns, or deep collection shafts.

Ultimate Corrosion Resistance

Forget once and for all about the damage caused by stagnant water. Thanks to the stainless steel impeller and reinforced shaft, the Maverick MV138 pump performs exceptionally well in corrosive or sandy environments. You can rely on it for continuous and demanding use, knowing that its internal parts are fully protected, offering you top durability.

Technical Specifications

  • Type: Submersible pump for sewage & rainwater
  • Power: 750 W
  • Maximum Flow Rate (Qmax): 12,500 lt/h
  • Maximum Head (Hmax): 8.0 m
  • Maximum Submersion Depth: 7.0 m
  • Maximum Solid Passage: 35 mm
  • Impeller / Shaft Material: Stainless steel
  • Suitable for: Basements, pits, tanks, excavations, flooded areas, and irrigation from troughs or cisterns

Manufacturer

Manufacturer Details

Warnings & Safety Information

Dimensions

Type
Waste Water / Sewage, Rainwater

Type

Waste Water / Sewage

Waste water / sewage pumps are used for pumping and transporting waste water, sewage, and other liquids containing solids or particles
Power Source
Electric

Power Source

Electric
The power supply refers to the pump's need for electrical energy from an external power source, such as single-phase or three-phase power.
Power
750 W

Power

It is the energy consumed by the motor to pump water. The greater the power, the more effectively it can lift and move water, especially over long distances or heights.

Features

Electronic Level Sensor
No

Electronic Level Sensor

It automatically activates the pump without the classic hanging float switch. It is ideal for narrow spaces and pits, as there is no risk of it getting stuck anywhere and flooding the area.
with Cutter Impeller
No

with Cutter Impeller

Components that chop, "cut" solid materials, such as organic waste or other particles, before they pass into the pump. They are mainly used in sewage or dirty water pumps, preventing clogging or damage to the system.
Float switch
No

Float switch

It is a mechanism that automatically controls the operation of the pump. When the water level reaches a predetermined height, the float activates the pump.
Vortex
No

Vortex

The vortex system in submersible water pumps uses vortex technology to create a rotating water current, which helps in the efficient transfer of water, even when it contains particles or solids.

Pumping Specifications

Maximum Head Height
8 m

Maximum Head Height: 8


The Maximum Head Height refers to the maximum height at which the pump can lift water against resistance (such as pipes or filters). As the head height increases, the pump's flow rate decreases.

  • The maximum head height is considered by manufacturers to be the point where the water will just barely reach.
  • The maximum performance is considered by manufacturers to be the water flow at 0-1 meter head height.
Maximum Output
12 m³/h

Maximum Output

The maximum output or flow of a submersible water pump, as defined by the manufacturers, is the maximum amount of water the pump can move under ideal conditions, usually with zero head (i.e., no lift resistance).
Maximum Particle Size
35 mm

Maximum Particle Size

Specifies the largest size of solid particles (such as sand, stones, or other impurities) that the device can pump without clogging or being damaged.
Shallow Suction
No

Shallow Suction

This function allows the pump to suck water from an extremely low level (up to 1-3 mm), ideal for flooded floors and basements.

Materials & Construction

Set
No
Stainless
Yes

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.