3D Printer Filament

3D Prima PrimaSelect PLA 1.75mm Black 0.75kg 1pc (Spool) 3D Printer Filament Code: PS-PLA-175-0750-BK

PrimaSelect PLA Matt filament is used in 3D printing to produce durable parts with a matte, slightly rough surface. It is made from pure PLA, contains no harmful additives, and is biodegradable. The...

PrimaSelect PLA Matt filament is used in 3D printing to produce durable parts with a matte, slightly rough surface. It is made from pure PLA, contains no harmful additives, and is biodegradable. The printing temperature ranges from 205 to 220 °C.

It adheres to BuildTak, PEI, and glass surfaces when used with an adhesive spray or PrimaFix. A heated print bed...

See full description See full description

Top specs

  • Weight 0.75 kg
  • Diameter 1.75 mm
  • See all
39 90 €
Delivery by Tue, 24 Nov
14,00 €   shipping cost
Sent from Greece
From Top Electronics 4.9 (38)

Learn more about invoicing

Description

Description

PrimaSelect PLA Matt filament is used in 3D printing to produce durable parts with a matte, slightly rough surface. It is made from pure PLA, contains no harmful additives, and is biodegradable. The printing temperature ranges from 205 to 220 °C.

It adheres to BuildTak, PEI, and glass surfaces when used with an adhesive spray or PrimaFix. A heated print bed is not required; if available, a temperature of 40 to 60 °C is recommended. The filament is laser-measured during production to monitor its diameter tolerance.

  • Material: PLA Matt
  • Color: Black
  • Diameter: 1.75 mm
  • Diameter tolerance: ±0.05 mm
  • Filament weight: 750 g
  • Packaging: Spool
  • Printing temperature: 205–220 °C
  • Melting temperature: 140–160 °C
  • Heated print bed: Not required
  • Compatible print surfaces: BuildTak, PEI, and glass with adhesive spray or PrimaFix
  • Moisture content: Low
  • Specific gravity: 1.38 g/cc
  • Melt flow rate: 14 g/10 min at 210 °C and a load of 2.16 kg
  • Tensile yield strength: 46.6 MPa
  • Yield strain: 2.1%
  • Elastic modulus: 3973 MPa

Manufacturer

See full description

Specifications

Specifications

Product Number
PS-PLA-175-0750-BK
Material
PLA
Colour
Black
Diameter
1.75 mm
Weight
0.75 kg
Filament Packaging
Spool
Quantity
1 pcs

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

See all specifications

Reviews (2)

Reviews

  1. 1
  2. 4 stars
    0
  3. 1
  4. 2 stars
    0
  5. 1 star
    0
Review this product

Reviews photos

Reviews photos
Reviews photos
Reviews photos
Reviews photos
Reviews photos

Reviews by our members

  • Τάσος Αθανασιάδης
    3
    0 out of 3 members found this review helpful

    I contacted them and they gave me advice but also the option to return it and have it checked for any defects (respect to their support). Below I will describe in detail the problem, generally a filament with increased difficulty in printing that may require raising the temperature up to 240 degrees to properly stick the layers and avoid gaps. When it printed correctly, the color and finish were very nice.

    In the first print, the infill was misshapen and weak, but there was also poor layer adhesion (the print split in half as soon as I removed it from the bed). Then I increased the temperature to 220 degrees (maximum recommended) and increased the flow (extrusion multiplier) to 130%. The second print came out fine, but the same problems were observed in the third print. Then, in larger prints, I noticed that the problem would appear intermittently and then resolve itself. A characteristic example is the gray component in the photo (printed with the filament in question, but I used filler putty to fix the problem), where some good layers are printed and then some layers with gaps.

    I tried several times to unclog the nozzle, but the problem did not go away. Finally, I used a White PRIMAVALUE filament in the printer and it printed fine.
    *I noticed that this particular filament (PRIMASELECT PLA Matt) has a rough surface (before printing), while all the other PLA filaments I have used are smooth.

    Translated from Greek ·
    Did you find this review helpful?
  • I contacted them and they gave me advice but also the option to return it and have it checked for any defects (respect to their support). Below I will describe in detail the problem, generally a filament with increased difficulty in printing that may require raising the temperature up to 240 degrees to properly stick the layers and avoid gaps. When it printed correctly, the color and finish were very nice.

    In the first print, the infill was misshapen and weak, but there was also poor layer adhesion (the print split in half as soon as I removed it from the bed). Then I increased the temperature to 220 degrees (maximum recommended) and increased the flow (extrusion multiplier) to 130%. The second print came out fine, but the same problems were observed in the third print. Then, in larger prints, I noticed that the problem would appear intermittently and then resolve itself. A characteristic example is the gray component in the photo (printed with the filament in question, but I used filler putty to fix the problem), where some good layers are printed and then some layers with gaps.

    I tried several times to unclog the nozzle, but the problem did not go away. Finally, I used a White PRIMAVALUE filament in the printer and it printed fine.
    *I noticed that this particular filament (PRIMASELECT PLA Matt) has a rough surface (before printing), while all the other PLA filaments I have used are smooth.

    Translated from Greek ·
    0
  • 0
  • See all

Description & Specifications

PrimaSelect PLA Matt filament is used in 3D printing to produce durable parts with a matte, slightly rough surface. It is made from pure PLA, contains no harmful additives, and is biodegradable. The printing temperature ranges from 205 to 220 °C.

It adheres to BuildTak, PEI, and glass surfaces when used with an adhesive spray or PrimaFix. A heated print bed is not required; if available, a temperature of 40 to 60 °C is recommended. The filament is laser-measured during production to monitor its diameter tolerance.

  • Material: PLA Matt
  • Color: Black
  • Diameter: 1.75 mm
  • Diameter tolerance: ±0.05 mm
  • Filament weight: 750 g
  • Packaging: Spool
  • Printing temperature: 205–220 °C
  • Melting temperature: 140–160 °C
  • Heated print bed: Not required
  • Compatible print surfaces: BuildTak, PEI, and glass with adhesive spray or PrimaFix
  • Moisture content: Low
  • Specific gravity: 1.38 g/cc
  • Melt flow rate: 14 g/10 min at 210 °C and a load of 2.16 kg
  • Tensile yield strength: 46.6 MPa
  • Yield strain: 2.1%
  • Elastic modulus: 3973 MPa

Manufacturer

Product Number
PS-PLA-175-0750-BK
Material
PLA
Colour
Black
Diameter
1.75 mm
Weight
0.75 kg
Filament Packaging
Spool
Quantity
1 pcs

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

Reviews (2)

  1. 1
  2. 4 stars
    0
  3. 1
  4. 2 stars
    0
  5. 1 star
    0
Review this product

Reviews photos

Reviews photos
Reviews photos
Reviews photos
Reviews photos
Reviews photos

Reviews by our members

  • Τάσος Αθανασιάδης
    3
    0 out of 3 members found this review helpful

    I contacted them and they gave me advice but also the option to return it and have it checked for any defects (respect to their support). Below I will describe in detail the problem, generally a filament with increased difficulty in printing that may require raising the temperature up to 240 degrees to properly stick the layers and avoid gaps. When it printed correctly, the color and finish were very nice.

    In the first print, the infill was misshapen and weak, but there was also poor layer adhesion (the print split in half as soon as I removed it from the bed). Then I increased the temperature to 220 degrees (maximum recommended) and increased the flow (extrusion multiplier) to 130%. The second print came out fine, but the same problems were observed in the third print. Then, in larger prints, I noticed that the problem would appear intermittently and then resolve itself. A characteristic example is the gray component in the photo (printed with the filament in question, but I used filler putty to fix the problem), where some good layers are printed and then some layers with gaps.

    I tried several times to unclog the nozzle, but the problem did not go away. Finally, I used a White PRIMAVALUE filament in the printer and it printed fine.
    *I noticed that this particular filament (PRIMASELECT PLA Matt) has a rough surface (before printing), while all the other PLA filaments I have used are smooth.

    Translated from Greek ·
    Did you find this review helpful?
  • I contacted them and they gave me advice but also the option to return it and have it checked for any defects (respect to their support). Below I will describe in detail the problem, generally a filament with increased difficulty in printing that may require raising the temperature up to 240 degrees to properly stick the layers and avoid gaps. When it printed correctly, the color and finish were very nice.

    In the first print, the infill was misshapen and weak, but there was also poor layer adhesion (the print split in half as soon as I removed it from the bed). Then I increased the temperature to 220 degrees (maximum recommended) and increased the flow (extrusion multiplier) to 130%. The second print came out fine, but the same problems were observed in the third print. Then, in larger prints, I noticed that the problem would appear intermittently and then resolve itself. A characteristic example is the gray component in the photo (printed with the filament in question, but I used filler putty to fix the problem), where some good layers are printed and then some layers with gaps.

    I tried several times to unclog the nozzle, but the problem did not go away. Finally, I used a White PRIMAVALUE filament in the printer and it printed fine.
    *I noticed that this particular filament (PRIMASELECT PLA Matt) has a rough surface (before printing), while all the other PLA filaments I have used are smooth.

    Translated from Greek ·
    0
  • 0
  • See all
39,90 €
14,00 €   shipping cost