Everything is fine with Xiaomi, but the international firmware, if I understand correctly, is "downgraded" compared to the Chinese ones in mesh functions. In any case, I will tell you that if you have the AX3600 router, you better forget about mesh. It is an amazing router (I have reviewed it) but when I tried to add the above as mesh nodes, it was a complete failure. From what I read in forums, this problem exists and (probably) is solved if someone installs the Chinese firmware. I did not do it.
Anyway, I bought them for the country house. There, my main router is an (excellent) Xiaomi AX3200 which, of course, could not cover the entire two-story house and the garden. I already had an AX3000 for one floor, which connected immediately and I was satisfied. There I also added the two AX3000NEs, easily and with excellent results. Without messing with firmware. In fact, the NEs even updated recently. And I kept the AX3000 I already had. The connection between the AX3200 on the 1st floor and the first AX3000NE is wired, and from there to the second AX3000NE is wireless. The AX3000NEs are placed in diagonally opposite corners of the ground floor but with line of sight between them. From the 2nd AX3000NE to the old AX3000 which is again on the 1st floor, I used a cable again. Everything works perfectly and I had no trouble with the installation. The whole house and the garden are perfectly covered.
I should note that if your network only has the provider's router, then the first AX3000NE can be set as the main router (even better by enabling DMZ. See how in the review I did on the AX3600.) and the second can be set as a mesh node.
Όλα καλά με τα Xiaomi, αλλά τα international firmware, αν καταλαβαίνω σωστά, είναι "ριγμένα" σε σχέση με τα κινέζικα στις λειτουργίες mesh. Όπως και να έχει θα σας πω ότι αν έχετε το router AX3600 καλύτερα ξεχάστε το mesh. Είναι φοβερό router (έχω κανει review) αλλά οταν πήγα να του προσθεσω τα παραπάνω ως mesh nodes, ήταν πλήρης η αποτυχία. Από ότι διάβασα σε forum, υπάρχει αυτό το πρόβλημα και (μάλλον) λύνεται αν κάποιος βάλει κινέζικο firmware. Δεν το έκανα.
Ούτως ή άλλως, τα αγόρασα για το εξοχικό. Εκεί, έχω βασικό router ένα (εξαιρετικό) Xiaomi AX3200 το οποίο φυσικά δεν μπορούσε να καλύψει όλο το διώροφο σπίτι και το κήπο. Ήδη είχα ένα AX3000 για τον ένα όροφο, το οποίο κούμπωσε αμέσως και ήμουν ευχαριστημένος. Εκεί προσθεσα και τα δυο AX3000NE, εύκολα και με εξαιρετικά αποτελέσματα. Χωρίς να μπλέξω με firmware. Μάλιστα τα NE έκαναν και update πρόσφατα. Και κράτησα και το AX3000 που ήδη είχα. Η σύνδεση μεταξύ του AX3200 που είναι στον 1ο όροφο, και του πρωτου AX3000NE είναι με καλώδιο και απο εκεί στο δεύτερο AX3000NE είναι ασύρματη. Τα AX3000NE είναι τοποθετημένα σε αντιδιαμετρικες γωνίες του ισογείου αλλά με οπτική επαφή μεταξύ τους. Από το 2ο AX3000NE προς το παλιό AX3000 που είναι πάλι στον 1ο όροφο έβαλα πάλι καλώδιο. Δουλεύουν όλα τέλεια και δεν δυσκολεύτηκα καθόλου στη τοποθέτηση. Καλύπτεται άριστα όλο το σπίτι και ο κήπος.
Πρέπει να σημειώσω ότι αν στο δίκτυο σας υπάρχει μόνο το router του provider, τότε μπορεί να μπει το πρώτο AX3000NE σαν βασικό router (Ακόμα καλύτερα ανοίγοντας DMZ. Δείτε πώς στο review που έχω κανει στο AX3600.) και το δευτερο να μπει ως mesh node.